How to select the #1 thrust washer on the Ford C4/C5 transmission.
There's been a lot of questions on how to select the correct #1 thrust washer on the C4/C5 tranny. Many people believe the #1 is used to set end play like on other transmissions but it's the #2 washer that sets the end play on the C4. The #1 washer is there to reduce the forward and aft movement of the direct drum on the stator support. Remember, the end play needs to be verified with the proper #2 washer before making this test. This clip which is in my full length C4 vol. 1&2 repair videos, explains how to determine the proper #1 washer size. For info on all my repair videos, please go to my web site www.BadShoeProductions.com
Видео How to select the #1 thrust washer on the Ford C4/C5 transmission. канала BadShoeProductions
Видео How to select the #1 thrust washer on the Ford C4/C5 transmission. канала BadShoeProductions
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
![Welcome to BadShoe Productions](https://i.ytimg.com/vi/WVoIKjF8_gk/default.jpg)
![What's New with BadShoe](https://i.ytimg.com/vi/K-zct_WvVbo/default.jpg)
![Rotating cycle of RC aircraft ownership.](https://i.ytimg.com/vi/HTgd-jnvq6E/default.jpg)
![Keeping a seal's garter spring from popping out during installation](https://i.ytimg.com/vi/5Kr6zaadsv4/default.jpg)
![How to install a centrifugal supercharger in a 96-97 4.6L Thunderbird part 2 (test fitting)](https://i.ytimg.com/vi/9nvO-MK6whw/default.jpg)
![How to install a centrifugal supercharger in a 96-97 4.6L Thunderbird, part 1 (preparation)](https://i.ytimg.com/vi/iWocsMYfw3E/default.jpg)
![How to install a centrifugal supercharger in a 96-97 4.6L Thunderbird, part 3 (parts installation)](https://i.ytimg.com/vi/4HHjwDMJa_g/default.jpg)
![How to install a centrifugal supercharger in a 96-97 4.6L Thunderbird, part 4 (last parts & startup)](https://i.ytimg.com/vi/opsBfN6MnZE/default.jpg)
![How to set the #1 thrust washer size on the Ford C4/C5 Transmission](https://i.ytimg.com/vi/3nX0EsEzWRs/default.jpg)
![Making air checks on the Ford C4 transmission](https://i.ytimg.com/vi/ucTqlOHhCxM/default.jpg)
![Introduction to BadShoe's Easy Tooling Products](https://i.ytimg.com/vi/mqQjZGeTV7I/default.jpg)
![How to use BadShoe's AODE/4R70W Servo & Accumulator tool](https://i.ytimg.com/vi/DS9V4DeKJQA/default.jpg)
![How to use BadShoe's AOD/4R70W piston sizer tools](https://i.ytimg.com/vi/ltzqGAY-jJ8/default.jpg)
![Troubleshooting a no start concern on a EEC 4 car HD](https://i.ytimg.com/vi/8lo3FVXH-ks/default.jpg)
![Making backlash adjustment on the Ford 9" rear.](https://i.ytimg.com/vi/bSCUck4M6W4/default.jpg)
![Rewiring a Ford EEC IV "speed density" harness to a "mass air" harness](https://i.ytimg.com/vi/mnnTgXkHU9Q/default.jpg)
![Easy installation of the Ford 8.8" traction-lok S-spring](https://i.ytimg.com/vi/O_TqMuV_MeA/default.jpg)
![How to use BadShoe's C6 and Fmx sizer tools](https://i.ytimg.com/vi/ZCgh24EOgqI/default.jpg)
![Making end play check on the Ford C4 tranny](https://i.ytimg.com/vi/As5lBDy107c/default.jpg)
![Ford 8.8" rear end Traction-Lok clutch setups](https://i.ytimg.com/vi/0GsLDg3C6Hc/default.jpg)