Rotating cycle of RC aircraft ownership.
Like all of you car guys, I have other hobbies. I've always been interested in radio control model airplanes and have started getting in to it. I found that there's a learning curve and a continues cycle in owning them. This one has been repaired three or four times. Each fix shows some scars and the performance is slightly different, kind of like a Drag car. See if your hobby has a similar cycle like this three minute video. A shout out to the RARC, Richmond Area RC club.
Видео Rotating cycle of RC aircraft ownership. канала BadShoeProductions
Видео Rotating cycle of RC aircraft ownership. канала BadShoeProductions
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
![How to select the #1 thrust washer on the Ford C4/C5 transmission.](https://i.ytimg.com/vi/IYH7oKSA-MY/default.jpg)
![Welcome to BadShoe Productions](https://i.ytimg.com/vi/WVoIKjF8_gk/default.jpg)
![What's New with BadShoe](https://i.ytimg.com/vi/K-zct_WvVbo/default.jpg)
![Keeping a seal's garter spring from popping out during installation](https://i.ytimg.com/vi/5Kr6zaadsv4/default.jpg)
![How to install a centrifugal supercharger in a 96-97 4.6L Thunderbird part 2 (test fitting)](https://i.ytimg.com/vi/9nvO-MK6whw/default.jpg)
![How to install a centrifugal supercharger in a 96-97 4.6L Thunderbird, part 1 (preparation)](https://i.ytimg.com/vi/iWocsMYfw3E/default.jpg)
![How to install a centrifugal supercharger in a 96-97 4.6L Thunderbird, part 3 (parts installation)](https://i.ytimg.com/vi/4HHjwDMJa_g/default.jpg)
![How to install a centrifugal supercharger in a 96-97 4.6L Thunderbird, part 4 (last parts & startup)](https://i.ytimg.com/vi/opsBfN6MnZE/default.jpg)
![How to set the #1 thrust washer size on the Ford C4/C5 Transmission](https://i.ytimg.com/vi/3nX0EsEzWRs/default.jpg)
![Making air checks on the Ford C4 transmission](https://i.ytimg.com/vi/ucTqlOHhCxM/default.jpg)
![Introduction to BadShoe's Easy Tooling Products](https://i.ytimg.com/vi/mqQjZGeTV7I/default.jpg)
![How to use BadShoe's AODE/4R70W Servo & Accumulator tool](https://i.ytimg.com/vi/DS9V4DeKJQA/default.jpg)
![How to use BadShoe's AOD/4R70W piston sizer tools](https://i.ytimg.com/vi/ltzqGAY-jJ8/default.jpg)
![Troubleshooting a no start concern on a EEC 4 car HD](https://i.ytimg.com/vi/8lo3FVXH-ks/default.jpg)
![Making backlash adjustment on the Ford 9" rear.](https://i.ytimg.com/vi/bSCUck4M6W4/default.jpg)
![Rewiring a Ford EEC IV "speed density" harness to a "mass air" harness](https://i.ytimg.com/vi/mnnTgXkHU9Q/default.jpg)
![Easy installation of the Ford 8.8" traction-lok S-spring](https://i.ytimg.com/vi/O_TqMuV_MeA/default.jpg)
![How to use BadShoe's C6 and Fmx sizer tools](https://i.ytimg.com/vi/ZCgh24EOgqI/default.jpg)
![Making end play check on the Ford C4 tranny](https://i.ytimg.com/vi/As5lBDy107c/default.jpg)
![Ford 8.8" rear end Traction-Lok clutch setups](https://i.ytimg.com/vi/0GsLDg3C6Hc/default.jpg)