Загрузка страницы

Honeycomb Blind installation instructions

Honeycomb blind installation instructions. eBlinds Australia https://eblindsaustralia.com.au/ 1800 325 463

Important: Exercise extreme caution when unpacking your new E blinds. Care must be taken when using knives or scissors as any cuts to the fabric or cord are not covered by warranty.
You will need: Tape measure, step ladder, pencil, screw drill
List of components:
Mounting brackets quantity 2 (Qty will vary depending on the Blind Width)
Hold down clips quantity 2
Child safety device quantity 1
Screws (for timber installation only)
Outside Mount bracket installation
Step 1: Measure your head rail width
Step 2: End bracket should be approximately 15cm from each end of the headrail. Space any remaining brackets if applicable evenly across the headrail no more than 50cm apart NOTE: Be sure that the bracket placement does not interfere with any components inside the headrail as shown below
Step 3: Hold the bracket in position and mark the holes for the screws through the back of the bracket with a pencil. The top of the bracket should be set to the height from where your original measurement was taken
Step 4: Using your pencil marks as a guide, start by predrilling the holes to avoid splitting the timber
Step 5: Hold the bracket in place and secure to the surface with the screws provided. For plaster, brick, steel or aluminium surfaces contact your local hardware store for the correct fittings. Ensure bracket is fitted as per the picture
Step 6: Insert the front lip into the corresponding slot on the headrail
Step 7: ensure the blind is centered on the window and then rotate the headrail backward toward the window until a click is heard. This means that the headrail is engaged into the brackets
Step 8: Be sure the blind is secured into each bracket before operating the blind
Inside Mount Bracket Installation
Step 1: Measure your head rail width
Step 2: End bracket should be approximately 15cm from each end of the headrail. Space any remaining brackets if applicable evenly across the headrail no more than 50cm apart NOTE: Be sure that the bracket placement does not interfere with any components inside the headrail as shown below
Step 3: Hold the bracket in position and mark the holes for the screws through the top or back of the brackets with a pencil
Step 4: Using your pencil marks as a guide, start by predrilling the holes to avoid splitting the timber
Step 5: Hold the bracket in place and secure to the surface with the screws provided. For plaster, brick, steel or aluminium surfaces contact your local hardware store for the correct fittings
Step 6: Insert the front lip into the corresponding slot on the headrail
Step 7: Ensure the blind is centered on the window and then rotate the headrail backward toward the window until a click is heard. This means that the headrail is engaged into its brackets
Step 8: Be sure the blind is secured into each bracket before operating the blind
If mounting onto a door you may wish to use the enclosed optional hold down clips:
With the blind at its full dropdown length place the pins on the hold brackets into the corresponding holes on the base rail and mark with a pencil where to drill your screw holes. Allow some wiggle room between the end of the base rail and the hold down clip to make it easier to remove the blind when required
Child Safety Device installation
Warning- Young children have died by wrapping loose curtain and blind cords or chains around their necks.
Secure chains with Child Safety Device supplied
Move cots and furniture away from window covering cords or chains
To avoid creating a possible strangulation hazard for children, this corded internal window covering must be installed in such a way that a loose chain cannot form a loop of 220MM or longer at a height of less than 1600mm above floor level
If the end of the chain loop is above 1.6 meters from floor level a Child Safety Device is not required
If the end of the chain loop is below 1.6 meters from floor level a Child Safety Device is required
Child safety device correctly installed
Installing the Child Safety Device
Step 1
- Locate the base of the chain loop
Step 2
- Open the Child Safety Device
Step 3
- Place the Child Safety Device over the chain
Step 4
- Swivel the Child Safety Device closed and back to its original position
Step 5
- Tighten the chain by pulling the Child Safety Device and chain downward NOTE: Don’t pull too tightly. Allow enough slack to allow for chain to still move freely
Step 6
- Screw Child Safety Device into wall, Architrave or window frame.
Note: The Child Safety Device can be screwed onto the wall from 3 entry points left, middle and right

Child Safety Device is not required If the end of the chain loop is more than 1.6 meters above floor level,
If the end of the chain loop is below 1.6 meters above floor level, the Child Safety Device is required
Child Safety Device is installed correctly
- E blinds Australia, you measure, you install, you save, you beauty

Видео Honeycomb Blind installation instructions канала eBlinds Australia
Показать
Комментарии отсутствуют
Введите заголовок:

Введите адрес ссылки:

Введите адрес видео с YouTube:

Зарегистрируйтесь или войдите с
Информация о видео
25 мая 2018 г. 7:01:10
00:06:16
Яндекс.Метрика