[12] RuiDa - Laser Status Light Installation - RDC6442, RDC6445, RDC6432, RDC6445GT5
I have been asked a few times now how to wire up an indicator light to signal when the laser is operating, so that when the cutting job has completed the light goes off.
This can also be used as a visual reminder that the machine is operating and to increase safety around the laser machine.
Some users have multiple machines operating at the same time in a noisy environment, so it can be a good indication that the machine has finished and they can set up for the next cutting project.
As a safety note, this indicator light is not designed so you can walk away from your laser machines and just monitor the light for when it is complete, as a laser machine can cause fire and should not be left unattended.
I will be installing this on the RuiDa Controller RDC6432G the same process is relevant for most RuiDa Controllers such as the RDC6442, RDC6445G, RDC6445T5
You will need a 24V LED or Indicator Lamp, I chose this 10-30V LED Light for this demonstration.
The wiring of this is pretty straightforward, Wiring Diagrams can be found at https://mwlaser.com.au/laser-on-status-light-installation/
The 1st diagram is for the RDC6432G controller, the main difference between this and other RuiDa controllers is the +24VDC power for the indicator light is gained by the mainboard +24V power connector, or you could also connect to the +24V (1) on this diagram 2nd bank from the bottom.
The 2nd diagram is for the RDC64XX controllers, including the RDC6442, RDC6445G and RDC6445GT5 controllers.
RDC6445GT5 - Touchscreen Controller - https://s.click.aliexpress.com/e/_9JFZHc
RDC6445G - https://s.click.aliexpress.com/e/_AfpI3M
RDC6432G - https://s.click.aliexpress.com/e/_9uKM0q
First you will mount your status indicator light, and run the wiring neatly inside the machine to the mainboard making sure to keep it secure and out of the way of any moving parts or fans.
Next connect the positive cable to the 24V terminal from your controller, and the negative connection from the indicator light is wired to the STATUS terminal on your controller.
Suggested Parts & Tools
24V LED LAMP - https://s.click.aliexpress.com/e/_A6VJYa
Ferrules & Crimping Tool - https://s.click.aliexpress.com/e/_AaUueS
Wire Strippers - https://s.click.aliexpress.com/e/_A9q4f4
18AWG Wire - https://s.click.aliexpress.com/e/_A4AZFu
To show your thanks and support you can buy me a coffee here https://www.buymeacoffee.com/mwlaser/
I hope this has been an informative video, If you would like to ask me a question about your machine, email askmatt@mwlaser.com.au If I don’t know the answer I will do my best to find the solution for you and it may be featured in a future Video.
NOTE: This is not a paid production or advertisement.
Show your support for MW Laser by Buying Matt a Coffee.
This can be done via our website https://www.buymeacoffee.com/mwlaser
Thanks for Visiting.
Until next time, take care
Cheers Matthew
Visit MW Laser https://www.mwlaser.com.au
Instagram https://www.instagram.com/mattsworksh...
Facebook https://www.facebook.com/groups/mwlaser
Email: askmatt@mwlaser.com.au
Видео [12] RuiDa - Laser Status Light Installation - RDC6442, RDC6445, RDC6432, RDC6445GT5 канала MW Laser
This can also be used as a visual reminder that the machine is operating and to increase safety around the laser machine.
Some users have multiple machines operating at the same time in a noisy environment, so it can be a good indication that the machine has finished and they can set up for the next cutting project.
As a safety note, this indicator light is not designed so you can walk away from your laser machines and just monitor the light for when it is complete, as a laser machine can cause fire and should not be left unattended.
I will be installing this on the RuiDa Controller RDC6432G the same process is relevant for most RuiDa Controllers such as the RDC6442, RDC6445G, RDC6445T5
You will need a 24V LED or Indicator Lamp, I chose this 10-30V LED Light for this demonstration.
The wiring of this is pretty straightforward, Wiring Diagrams can be found at https://mwlaser.com.au/laser-on-status-light-installation/
The 1st diagram is for the RDC6432G controller, the main difference between this and other RuiDa controllers is the +24VDC power for the indicator light is gained by the mainboard +24V power connector, or you could also connect to the +24V (1) on this diagram 2nd bank from the bottom.
The 2nd diagram is for the RDC64XX controllers, including the RDC6442, RDC6445G and RDC6445GT5 controllers.
RDC6445GT5 - Touchscreen Controller - https://s.click.aliexpress.com/e/_9JFZHc
RDC6445G - https://s.click.aliexpress.com/e/_AfpI3M
RDC6432G - https://s.click.aliexpress.com/e/_9uKM0q
First you will mount your status indicator light, and run the wiring neatly inside the machine to the mainboard making sure to keep it secure and out of the way of any moving parts or fans.
Next connect the positive cable to the 24V terminal from your controller, and the negative connection from the indicator light is wired to the STATUS terminal on your controller.
Suggested Parts & Tools
24V LED LAMP - https://s.click.aliexpress.com/e/_A6VJYa
Ferrules & Crimping Tool - https://s.click.aliexpress.com/e/_AaUueS
Wire Strippers - https://s.click.aliexpress.com/e/_A9q4f4
18AWG Wire - https://s.click.aliexpress.com/e/_A4AZFu
To show your thanks and support you can buy me a coffee here https://www.buymeacoffee.com/mwlaser/
I hope this has been an informative video, If you would like to ask me a question about your machine, email askmatt@mwlaser.com.au If I don’t know the answer I will do my best to find the solution for you and it may be featured in a future Video.
NOTE: This is not a paid production or advertisement.
Show your support for MW Laser by Buying Matt a Coffee.
This can be done via our website https://www.buymeacoffee.com/mwlaser
Thanks for Visiting.
Until next time, take care
Cheers Matthew
Visit MW Laser https://www.mwlaser.com.au
Instagram https://www.instagram.com/mattsworksh...
Facebook https://www.facebook.com/groups/mwlaser
Email: askmatt@mwlaser.com.au
Видео [12] RuiDa - Laser Status Light Installation - RDC6442, RDC6445, RDC6432, RDC6445GT5 канала MW Laser
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
Revised Upgrade Guide From TopWisdom to Ruida for Co2 Laser Machine.Recycled Pallet Breakfast Tray (Ft. Cassie)Laser Y Axis Selector Relay - Rotary Axis & Gantry AxisCo2 Laser Project - Coasters Using LightBurn Circular Array ToolHOW TO TIPS How to use a router to add finishing touches to a chopping boardHow to Cut Circles using a Router Jig. Easy to Make Jig For Timber Router.MW Laser - LightBurn Material Test Pattern - Training VideoMW Laser J Series Rotary Attachments - J630 & J750 Models - Training VideoIntroduction to MW Laser - Our Range at a GlanceLive Stream - Co2 Laser Engraving 80W Laser - Cheeseboard[11] - RuiDa BWK301R Wireless Handle - RDC64xxG Co2 Laser ControllersRotary Stepper Driver Installation - Co2 Laser - RuiDa RDC6445GT5 TouchScreen - Cloudray CR139005 Build Your Own Laser - Tube & Mirror Mounts + Stepper MotorsZ Axis Upgrade on Red & Black Co2 Laser with Ruida Controller04 Build Your Own Laser Enclosure & Rail MountsCo2 Laser Lens Selection & Ramp Test[07] RuiDa Controller - RD Works - Cut OptimizationAdirondak ChairAdjusting The X & Y Belts On Co2 Laser Engraving Machine - Chinese 80W CNC Laser Cutting MachineEp.1 - LASER ROTARY ATTACHMENTS - Intro, Motors, Drivers Setup & Wiring. - CNC Rotary AxisImprove Engraving Quality (Correct Scan Offset) on CNC Co2 Laser RD Works/LightBurn Software Config