Form Tool Demonstration
This is a form tool I made to produce a large quantity of small tapered brass pins with a full radius on the end. It consists of two identical hardened cutters clamped to a pin that both aligns the cutters and provides a shank to hold the tool in a drill chuck. It cuts similar to a pencil sharpener.
Видео Form Tool Demonstration канала Toms Techniques
Видео Form Tool Demonstration канала Toms Techniques
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
![Stack Blocks Part Five - Making the Shaft and Final Assembly](https://i.ytimg.com/vi/RrwghU-BnFM/default.jpg)
![Hard Drive Deactivation With Cannon](https://i.ytimg.com/vi/HOh3d6deKec/default.jpg)
![Stack Blocks Part Four- Drilling the Holes and Milling the Corner Radii](https://i.ytimg.com/vi/4OyyyX_0K1E/default.jpg)
![Carriage Stop Clamp Part One, Sawing the Stock and Squaring Up the Part](https://i.ytimg.com/vi/uHI2X9iqqNI/default.jpg)
![Building a Stevens Single Shot Rifle, Part Three - The Stock, Mainspring and Target Sight](https://i.ytimg.com/vi/y_Zplr-a84Q/default.jpg)
![How to Grind a Sheet Metal Drill](https://i.ytimg.com/vi/XA8L4L30TyI/default.jpg)
![The New Toms Techniques Shop](https://i.ytimg.com/vi/sqGvsWETfkg/default.jpg)
![Stack Blocks Part One - INTRODUCTION](https://i.ytimg.com/vi/9T6ZTYZGOz0/default.jpg)
![A Simple Power Drawbar](https://i.ytimg.com/vi/stxUtoRe1AA/default.jpg)
![Carriage Stop Clamp Part Two, Drilling the Holes and Milling the Notch](https://i.ytimg.com/vi/8dJGXY8wZwU/default.jpg)
![Indicate the vise on a milling machine in just one pass](https://i.ytimg.com/vi/DdgSxoTmtx0/default.jpg)
![Making Scope Rings for the Browning A Bolt 3 - Part Four](https://i.ytimg.com/vi/d3Qc6rOsz9s/default.jpg)
![Welcome Back!](https://i.ytimg.com/vi/hq17Io3I7SA/default.jpg)
![Center a Rotary Table in Under a Minute Without an Indicator](https://i.ytimg.com/vi/GjezShYnoEU/default.jpg)
![Carriage Stop Thimble Part One, Order of Operations and Calculating the Ideal Diameter for the Knurl](https://i.ytimg.com/vi/3WbBCLF0Go8/default.jpg)
![Clamp Knurling Tool, Introduction](https://i.ytimg.com/vi/prlQXvXJLDk/default.jpg)
![Clamp Knurling Tool Body, Introduction](https://i.ytimg.com/vi/DF8CMvtZusk/default.jpg)
![Cutting an Internal Thread on the Atlas Lathe, Part Three - Cutting the Thread](https://i.ytimg.com/vi/c-V9wS0LIMo/default.jpg)
![Clamp Knurling Tool, Body, Squaring the Stock and Boring the Center Hole](https://i.ytimg.com/vi/I4AZAibbd_w/default.jpg)
![Clamp Knurling Tool Body, Milling the Slot](https://i.ytimg.com/vi/YlPwSScKYEk/default.jpg)