Stack Blocks Part Four- Drilling the Holes and Milling the Corner Radii
In this fourth part of the series on building the stack blocks, we drill and countersink the holes in the base, middle and top plates, doing multiple parts at once to save time. We also mill the corner radii to finish off the parts.
Видео Stack Blocks Part Four- Drilling the Holes and Milling the Corner Radii канала Toms Techniques
Видео Stack Blocks Part Four- Drilling the Holes and Milling the Corner Radii канала Toms Techniques
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
![Stack Blocks Part Five - Making the Shaft and Final Assembly](https://i.ytimg.com/vi/RrwghU-BnFM/default.jpg)
![Hard Drive Deactivation With Cannon](https://i.ytimg.com/vi/HOh3d6deKec/default.jpg)
![Carriage Stop Clamp Part One, Sawing the Stock and Squaring Up the Part](https://i.ytimg.com/vi/uHI2X9iqqNI/default.jpg)
![Building a Stevens Single Shot Rifle, Part Three - The Stock, Mainspring and Target Sight](https://i.ytimg.com/vi/y_Zplr-a84Q/default.jpg)
![How to Grind a Sheet Metal Drill](https://i.ytimg.com/vi/XA8L4L30TyI/default.jpg)
![The New Toms Techniques Shop](https://i.ytimg.com/vi/sqGvsWETfkg/default.jpg)
![Stack Blocks Part Two - Sawing Out the Stock](https://i.ytimg.com/vi/3Ompf_SWMso/default.jpg)
![Stack Blocks Part One - INTRODUCTION](https://i.ytimg.com/vi/9T6ZTYZGOz0/default.jpg)
![A Simple Power Drawbar](https://i.ytimg.com/vi/stxUtoRe1AA/default.jpg)
![Form Tool Demonstration](https://i.ytimg.com/vi/uIRlJz-xQKE/default.jpg)
![Carriage Stop Clamp Part Two, Drilling the Holes and Milling the Notch](https://i.ytimg.com/vi/8dJGXY8wZwU/default.jpg)
![Indicate the vise on a milling machine in just one pass](https://i.ytimg.com/vi/DdgSxoTmtx0/default.jpg)
![Making Scope Rings for the Browning A Bolt 3 - Part Four](https://i.ytimg.com/vi/d3Qc6rOsz9s/default.jpg)
![Welcome Back!](https://i.ytimg.com/vi/hq17Io3I7SA/default.jpg)
![Center a Rotary Table in Under a Minute Without an Indicator](https://i.ytimg.com/vi/GjezShYnoEU/default.jpg)
![Carriage Stop Thimble Part One, Order of Operations and Calculating the Ideal Diameter for the Knurl](https://i.ytimg.com/vi/3WbBCLF0Go8/default.jpg)
![Clamp Knurling Tool, Introduction](https://i.ytimg.com/vi/prlQXvXJLDk/default.jpg)
![Clamp Knurling Tool Body, Introduction](https://i.ytimg.com/vi/DF8CMvtZusk/default.jpg)
![Cutting an Internal Thread on the Atlas Lathe, Part Three - Cutting the Thread](https://i.ytimg.com/vi/c-V9wS0LIMo/default.jpg)
![Clamp Knurling Tool, Body, Squaring the Stock and Boring the Center Hole](https://i.ytimg.com/vi/I4AZAibbd_w/default.jpg)