Flashforge Dreamer (NX) - Hatchbox Gold PETG 1.75mm Filament Testing - Part 1
This two-part video shows the testing of Hatchbox Gold PETG 1.75mm Filament.
Part 1 shows unboxing, and using a Temperature Tower to evaluate the best extrusion temperature to use.
Part 2 covers further Bed and Layer Adhesion testing while adjusting the layer height to see what the limit is for this filament. The product I'm printing with this has tall sides and at 0.2mm layer height, takes 10+ hours to print. By using a thicker layer height I'm hoping to cut that down quite a bit. But the layer adhesion needs to be strong and I want to the sides to look good, so there's a tradeoff.
Adjusting the printing speed and the fan speed turns out to be the key for the best layer adhesion.
At the end I compare the results of using Hatchbox and Polymaker Gold PETG to make the final product and declare the winner.
Link to Sabacc Pot Tray on my Etsy Store:
https://betacygnidesigns.etsy.com/listing/1261118300/sabacc-pot-tray-pspa-approved?utm_source=Copy&utm_medium=ListingManager&utm_campaign=Share&utm_term=so.lmsm&share_time=1694613832264
Link to Hatchbox Gold PETG Filament 1.75mm on Amazon:
https://smile.amazon.com/gp/product/B01C6BRXLY/
Link to Polymaker Gold PETG Filament 1.75mm on Amazon:
https://smile.amazon.com/gp/product/B09H2SHPD9/
Link to Temperature Tower Thingiverse Project:
https://www.thingiverse.com/thing:4356906
Link to Bed Adhesion and Layer Cracking Test
https://www.thingiverse.com/thing:4536632
Link to 3dBenchy on Thingiverse:
https://www.thingiverse.com/thing:763622
These are the spatulas I used to help remove the pieces from the print bed:
https://smile.amazon.com/gp/product/B075SLTY8B/
These are the tweezers I used to help remove dripping filament from the print head:
https://smile.amazon.com/gp/product/B0845SKD7Z/
This is the wire brass brush I use to clean the nozzle tip:
https://smile.amazon.com/gp/product/B01J2BS92S/
Flashforge Dreamer NX on Amazon:
https://smile.amazon.com/gp/product/B07DPBRCYZ/
OpenSCAD website:
https://www.openscad.org/
I used Simplify3D slicer software for the test:
https://www.simplify3d.com/
-------------------
Link to my Etsy Store:
https://betacygnidesigns.etsy.com/
---------------------
Music:
"Blippy Trance" Kevin MacLeod (incompetech.com)
Licensed under Creative Commons: By Attribution 4.0 License
http://creativecommons.org/licenses/by/4.0/
---------------------
End Screen Video Acknowledgement: Cosmic Reef Video produced by NASA and the Space Telescope Science Institute (STScI).
https://hubblesite.org/contents/media/videos/2020/16/1277-Video
Видео Flashforge Dreamer (NX) - Hatchbox Gold PETG 1.75mm Filament Testing - Part 1 канала Beta Cygni
Part 1 shows unboxing, and using a Temperature Tower to evaluate the best extrusion temperature to use.
Part 2 covers further Bed and Layer Adhesion testing while adjusting the layer height to see what the limit is for this filament. The product I'm printing with this has tall sides and at 0.2mm layer height, takes 10+ hours to print. By using a thicker layer height I'm hoping to cut that down quite a bit. But the layer adhesion needs to be strong and I want to the sides to look good, so there's a tradeoff.
Adjusting the printing speed and the fan speed turns out to be the key for the best layer adhesion.
At the end I compare the results of using Hatchbox and Polymaker Gold PETG to make the final product and declare the winner.
Link to Sabacc Pot Tray on my Etsy Store:
https://betacygnidesigns.etsy.com/listing/1261118300/sabacc-pot-tray-pspa-approved?utm_source=Copy&utm_medium=ListingManager&utm_campaign=Share&utm_term=so.lmsm&share_time=1694613832264
Link to Hatchbox Gold PETG Filament 1.75mm on Amazon:
https://smile.amazon.com/gp/product/B01C6BRXLY/
Link to Polymaker Gold PETG Filament 1.75mm on Amazon:
https://smile.amazon.com/gp/product/B09H2SHPD9/
Link to Temperature Tower Thingiverse Project:
https://www.thingiverse.com/thing:4356906
Link to Bed Adhesion and Layer Cracking Test
https://www.thingiverse.com/thing:4536632
Link to 3dBenchy on Thingiverse:
https://www.thingiverse.com/thing:763622
These are the spatulas I used to help remove the pieces from the print bed:
https://smile.amazon.com/gp/product/B075SLTY8B/
These are the tweezers I used to help remove dripping filament from the print head:
https://smile.amazon.com/gp/product/B0845SKD7Z/
This is the wire brass brush I use to clean the nozzle tip:
https://smile.amazon.com/gp/product/B01J2BS92S/
Flashforge Dreamer NX on Amazon:
https://smile.amazon.com/gp/product/B07DPBRCYZ/
OpenSCAD website:
https://www.openscad.org/
I used Simplify3D slicer software for the test:
https://www.simplify3d.com/
-------------------
Link to my Etsy Store:
https://betacygnidesigns.etsy.com/
---------------------
Music:
"Blippy Trance" Kevin MacLeod (incompetech.com)
Licensed under Creative Commons: By Attribution 4.0 License
http://creativecommons.org/licenses/by/4.0/
---------------------
End Screen Video Acknowledgement: Cosmic Reef Video produced by NASA and the Space Telescope Science Institute (STScI).
https://hubblesite.org/contents/media/videos/2020/16/1277-Video
Видео Flashforge Dreamer (NX) - Hatchbox Gold PETG 1.75mm Filament Testing - Part 1 канала Beta Cygni
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
USS Hornet Restoration of Grumman US2B Tracker #ShortsMika3D Shiny Silk Silver PLA Testing on Flashforge Dreamer NX 3d Printer - Part 2Mika3D Shiny Silk Silver PLA Testing on Flashforge Dreamer NX 3d Printer - Part 1Flashforge Dreamer (NX) - Cold Weather PrintingReplacing a Pull-up Bar on a Play StructureGreen Army Men @ Disney California Adventure #ShortsReplacing a French Drain Sump Pump - Part 23D Printing - How Long Does the Heat Break Tube Last? - Part 2Building Garden Steps on a 20 Degree Slope - Part 1Hun Skal Leve (Hunskaleva) #ShortsWalt Disney World Fruit BatSnow Peak Bipod Stove With MSR WindscreenSea Lions at Elkhorn Slough #ShortsDik Dik Eating #ShortsSnorkeling on the Kona Coast #ShortsFlashforge Dreamer (NX) - Replacing Printhead & Nozzle plus switching to a Silicone Sock - Part 2Flashforge Dreamer (NX) - Testing HQA PETG Filament - Part 1Calibrating Your LG TV Yourself!Flashforge Dreamer (NX) - FilaCube Gray PLA - Testing & Millennium Falcon Dice Tower - Part 2Flashforge Dreamer (NX) - Getting Amazon Basics PLA Filament to Print ReliablyEvolution Rage 4 Chop Saw Custom Stop Block