How to Replace Timing Belt, Water Pump, and Pulley's for Honda/Acura V6 J-Series Engines

In this video, I will show you how to perform a timing belt service. The belt needs to be replaced every 105k miles before it becomes too brittle and snaps. Many Honda and Acura vehicles have "interference" engines where if the timing belt breaks, the valves and pistons will collide and destroy your engine. You should also replace the water pump, serpentine belt, and power steering belt while everything is taken apart.
I will be demonstrating this on my 2002 Acura TL-S with a V6 J32A2 engine. This will be a very similar process for other vehicles also using a V6 J-Series engine including the Honda Accord, Odyssey, Pilot, Ridgeline, Passport, Legend, Inspire, & Acura RL, TL, CL, MDX, RDX, ZDX.

Other Insightful Videos:
- How to Remove Crankshaft bolt - Bump Start Method:
https://youtu.be/wG3SZ6PecbA?t=201
https://youtu.be/exSqtZ6j2CY?t=273
https://youtu.be/VOFc3Iby0TY
- How to Replace Engine Mounts: https://youtu.be/aCG4y8XlC2I
- How to Replace Coolant: https://youtu.be/S1qX39OTyAQ

Tools used in this video:
- 50mm Crankshaft Pulley Holder
Buy - https://amzn.to/3MybzNm
Rent - https://www.autozone.com/shop-and-garage-tools/loaner-parts-puller-installer-tools/p/oemtools-honda-acura-crankshaft-damper-harmonic-balancer-holding-tool/420315_0_0?cmpid=LIA:US:EN:AD:NL:1000000:TLS:19489353547&&CATARGETID=120054150001289921&CADevice=c&gclid=EAIaIQobChMI24HXqor8_gIVuPTjBx2ttApvEAQYASABEgLVt_D_BwE&gclsrc=aw.ds
- Serpentine Belt Tool
Buy - https://amzn.to/435AwVO
Rent - https://www.autozone.com/loan-a-tools/loaner-serpentine-belt-tool/p/oemtools-serpentine-belt-tool-kit-for-removal-and-installation-of-serpentine-belts-9-piece/298547_0_0
- Honda Genuine COOLANT (Type-2) (OL999-9011) - https://amzn.to/3q7Re9b
- Door Panel/Upholstry/Clip Removal Tool - https://amzn.to/3OxIqAs
- 8mm Honda Clips - 91512-sx0-003 - https://amzn.to/3yuOdkQ
- 10mm Honda Clips - 91503-sz5-003 - https://amzn.to/3y9HMCe
- 1/4" ID Vinyl Tubing - https://amzn.to/43H5rHY
- Paint Marker - https://www.meijer.com/shopping/product/elmer-s-painters-opaque-paint-marker-medium-point-white-1-ct/7994607333.html
- 19mm Lisle Weighted Impact Socket - https://amzn.to/3BzBcY2

Parts you'll need to replace:
Timing Belt - 14400-P8A-A02
Power Steering Belt - 56992-P8A-305
Serpentine/Drive Belt - 38920-P8C-A02
Water Pump - 19200-P8A-A02
Timing Belt Tensioner - 14520-P8E-A01

Optional Parts to Replace:
Timing Belt Tensioner Pulley - 14510-PGE-A01
Idler Pulley - 14550-PGE-A01
Serpentine/Drive Belt Pulley/Tensioner - 31170-P8F-A01
Oil Dip Stick Tube O-Ring - 91302-GE0-000

Parts to replace only if absolutely necessary:
Camshaft Oil Seals - 91214-P8A-A01
Crankshaft Oil Seal - 91212-P8A-A01

INTRODUCTION, INSPECTION, & PARTS
0:00 Introduction
0:52 Serpentine Belt Tensioner Inspection
1:32 Purchasing Tools and Parts
6:25 Comparing Old vs New Pulley's

TIMING BELT REMOVAL
8:35 Turn Heat & Fans to Max Setting
8:50 Remove Front Passenger Wheel & Splash Shield
9:29 Remove Harmonic Balancer/Crankshaft Pulley Bolt
10:58 Remove Fender Lining
11:31 Remove Serpentine/Drive Belt
12:08 Remove Intake Manifold Covers
12:25 Remove Side Engine Mount Bracket
14:04 Remove Power Steering Belt
14:33 Remove Engine Oil Dipstick Tube
14:57 Remove Serpentine/Drive Belt Pulley/Tensioner
15:16 Remove Upper Timing Belt Covers
16:08 Set the Driveshaft & Camshaft Pulley's to Top Dead Center (TDC)
17:55 Remove Crankshaft Pulley & Lower Timing Belt Cover
18:06 Mark TDC lines with paint marker on timing belt
19:18 Remove Cruise Control Module
19:55 Remove Side Engine Mount
20:48 Remove Engine Mounting Bracket
21:25 Remove Idler Pulley
21:36 Remove Timing Belt
21:44 Remove Timing Belt Tensioner & Tensioner Pulley
21:57 Copy TDC Marks over to New Timing Belt
23:15 Drain Coolant from Radiator, Reservoir, & Engine Block
25:43 Remove Water Pump

TIMING BELT INSTALLATION
27:14 Install Water Pump 8.5ft.lbs
27:38 Install Timing Belt Tensioner Pulley 19ft.lbs
27:55 Loosely install Idler Pulley
28:04 Install Timing Belt
31:13 Torque Idler Pulley bolt to 33ft.lbs
31:25 Install Timing Belt Tensioner 8.5ft.lbs
31:34 Remove Timing Belt Tensioner Retainer Pin
31:57 Install Engine Mounting Bracket 33ft.lbs
32:37 Loosely Install PS Mounting Bolts
32:51 Install Timing Belt Guide Plate & Timing Belt Covers
33:14 Install Serpentine/Drive Belt Tensioner/Pulley 8.5ft.lbs
33:26 Install Engine Oil Dipstick Tube
33:58 Install Crankshaft Pulley & Bolt 181ft.lbs
34:40 Install Power Steering Belt
35:04 Adjust PS Belt Tension
35:41 Torque PS Pump Mounting Bolts to 17ft.lbs
35:55 Install Serpentine/Drive Belt
37:05 Loosely Install Side Engine Mount, Bracket, & Bracket-to-Mount Bolt
37:29 Torque Side Engine Mount Bolts to 40ft.lbs
37:41 Torque Side Engine Mount Bracket Bolts to 33ft.lbs
37:51 Torque Side Bracket-to-Mount Bolt to 40ft.lbs
38:07 Install Cruise Control Module
38:18 Install Splash Shield & Fender Lining
38:35 Install Wheel 80ft.lbs & Intake Manifold Covers
38:41 Refill Coolant
42:00 Conclusion
Incineration Incin3ration

Видео How to Replace Timing Belt, Water Pump, and Pulley's for Honda/Acura V6 J-Series Engines канала Car Repairs Made Simple