Загрузка страницы

Pattern drive Shog Time setting. Tricot Warp Knitting Machine. Karl Mayer. 트리코트 오버래핑 타이밍 설정 섬유 원단 니트

Let's look at how to set the overlapping motion of a general machine.
The criterion of the description is the Tricot Karl Meyer machine.
Let's look at the gauge chart to match the overlapping motion or timing by machine type.
Gauge dimensions vary according to the machine type and motion number.
The HKS-2 type is 6.5mm and the HKS 3.4 type is 7.5mm, and there are also 7mm and 11mm type machines.
4 Tempi setting gauges are all 32mm.
This is the gauge for each dimension specified in the reference table.
The one above is for 3 tempi, and in the middle is for 3 tempi and 4 tempi made by Hanyoung Machinery, and the width 32mm gauge is for 4 tempi.
It is of utmost importance to stop the machine at the specified position for accurate setting of the overlapping motion.
Only when it stops accurately at the designated position, perfect operation is achieved after setting the gauge.
The main shaft has a crank angle key and a pulley lock key.
If the angle key is located in the center of the bottom, the cam is 180 degrees and the position may be different depending on the machine type.
It is a gauge to check the operation of the crank drive, and it is a necessary equipment to set the correct operation of the unit.
If the cam angle reference point key is located in the center of the bottom, you can see that it is 180 degrees on the gauge.
Stop the machine at this point.
Alternatively, when reaching the highest point of the guide bar lever, the crankshaft is 180 degrees
Stop the machine at this point and adjust it with a timing gauge to get accurate motion.
Also, if you stop at the highest point of the needle, the cam is positioned 180 degrees, so you can set the timing.
When the machine is stopped in the manner described previously, the pattern wheel will be in this position.
However, if it is located on the inclined surface of the pattern wheel, when the push wire pulls the pattern drive fixing clamp, it slides and the position of the pattern wheel is
It is shifted, making adjustments difficult.
Place the setting gauge on the sliding unit rail.
Then loosen the pattern driver fixing clamp.
This should be done after stopping the machine in the correct position before timing.
3 This is the timing setting of Tempe. After turning the pattern driver main shaft, adjust the key so that it touches the gauge as shown in the video you are watching, and then fix the clamp.
The height of the 4 tempi gauge is 32mm and the setting method is the same as the 3 tempi described above.
Before adjustment, mark the position on the pattern drive axis and then adjust it to check the degree of movement. If adjustment is not possible, you can return to the original position.
If the timing operation is incorrect, there are many side effects, such as friction with the needle, as well as being very sensitive when using a high tissue number and not being able to feed the thread.
When the pattern drive axis is turned clockwise, the motion becomes faster.
For precise adjustment, it should move 2~3mm.
If you turn it counterclockwise, the motion will be slow.
After adjustment, you must check the machine operation status.
When all the adjustments are done, lock the clamp and remove the 10mm pattern key and you're done.
Overlapping operation, that is, when the organization number is 10/34, the moment the guide changes from No. 1 to No. 0 or No. 3 to No. 4, the guide moves from No. 1 to No. 0 as soon as it leaves the needle and passes through without friction with the needle.
On this screen, you are seeing the phenomenon that the overlapping motion starts quickly and hits the needle before the guide exits the needle.
In this case, the motion is fast, so you need to adjust it so that it happens late.
Conversely, the overlapping operation is late.
It is a situation where the guide runs when it exits the needle and enters again, so it collides with the needle.
In this case, it is necessary to adjust it so that the movement takes place quickly.
That is all. Thank you.
제12강
트리코트 일반 기계 패턴 디스크 타이밍(오버래핑) 동작 설정 설명.
You may not be able to express it properly because you used an English translator.
Hello, this is Choi Sang-don.

Видео Pattern drive Shog Time setting. Tricot Warp Knitting Machine. Karl Mayer. 트리코트 오버래핑 타이밍 설정 섬유 원단 니트 канала Warp knitting Techniques
Показать
Комментарии отсутствуют
Введите заголовок:

Введите адрес ссылки:

Введите адрес видео с YouTube:

Зарегистрируйтесь или войдите с
Информация о видео
9 октября 2020 г. 14:32:46
00:04:22
Другие видео канала
01 RACOP 4 170" E12 3 bars stitching SITM 201701 RACOP 4 170" E12 3 bars stitching SITM 2017Lec 38_Warp Knitting (Overlap, Underlap, Swinging Motion, Shogging Motion)Lec 38_Warp Knitting (Overlap, Underlap, Swinging Motion, Shogging Motion)Changing the pattern drum repeat (Tempi) ratio. Tricot Warp Knitting Machine. Karl mayer. 트리코트 원단 니트Changing the pattern drum repeat (Tempi) ratio. Tricot Warp Knitting Machine. Karl mayer. 트리코트 원단 니트Operate Tricot machine basic guideOperate Tricot machine basic guidePattern drive Shog setting. Tricot Warp Knitting Machine. Karl Mayer. design. 트리코트 패턴 타이밍설정 섬유 원단 니트Pattern drive Shog setting. Tricot Warp Knitting Machine. Karl Mayer. design. 트리코트 패턴 타이밍설정 섬유 원단 니트The Structure of Warp Knits. Basic Designing Principles. Tricot Warp Knitting. karl mayer 트리코트 조직 기초The Structure of Warp Knits. Basic Designing Principles. Tricot Warp Knitting. karl mayer 트리코트 조직 기초I turn Washing Machine Motor into 220v electric GeneratorI turn Washing Machine Motor into 220v electric GeneratorGuide position setting. Tricot Warp Knitting Machine. Karl Mayer. design.트리코트 기계 가이드위치 조정(섬유 원단 니트)Guide position setting. Tricot Warp Knitting Machine. Karl Mayer. design.트리코트 기계 가이드위치 조정(섬유 원단 니트)Motion of pattern disk. Tricot Warp Knitting Machine. fabric design karl mayer.트리코트 패턴디스크동작 섬유 원단 니트Motion of pattern disk. Tricot Warp Knitting Machine. fabric design karl mayer.트리코트 패턴디스크동작 섬유 원단 니트Karl Mayer Presents: Our MachinesKarl Mayer Presents: Our MachinesInnovative Production by KARL MAYERInnovative Production by KARL MAYERKNITXMAX WARP KNOTTING OPERATION INSTRUCTIONKNITXMAX WARP KNOTTING OPERATION INSTRUCTIONSITM Innovative Pattern  Drive ControlSITM Innovative Pattern Drive ControlITMA 2019 KARL MAYER HKS 3-M-ONITMA 2019 KARL MAYER HKS 3-M-ONMachine-Made Lace | How It's MadeMachine-Made Lace | How It's MadeHKS 3M-ON 2900 RPM KARL MAYERHKS 3M-ON 2900 RPM KARL MAYERPROSIZE ® – A sizing machine for spun yarns by KARL MAYERPROSIZE ® – A sizing machine for spun yarns by KARL MAYERBasic Lapping Movements. Lapping start position and fabric loop shape. Tricot Warp Knitting. 트리코트 조직Basic Lapping Movements. Lapping start position and fabric loop shape. Tricot Warp Knitting. 트리코트 조직BQ198 warp knotting machine, warp tying machine for warp knitting machine and weaving loomsBQ198 warp knotting machine, warp tying machine for warp knitting machine and weaving loomsLapping Diagram and Chain Notations. Structure of Warp Knitting. Tricot. Karl mayer. 트리코트 원단 조직 구성원리Lapping Diagram and Chain Notations. Structure of Warp Knitting. Tricot. Karl mayer. 트리코트 원단 조직 구성원리
Яндекс.Метрика