sea flea mini max timelapse build 2016
Only takes 8 minutes to build a sea flea - who knew?
8 day build and test runs of a mini max with 9.9 Merc. somewhere in the Haliburton Highlands Ontario. Commentary with time tags below:
0:26 - had to replace switch on old table saw
0:58 - twisting together the bow to close the "gore" was a gruesome task - lots small passes removing material with circular saw
2:20 - about this point we realized nothing lined up the way it does in the plans...the stringers were too short!...PL premium 8X used to fill the gap...then lots of sanding/rasping
3:05 - also added a second transom pad between the stringers to ensure PL was not the only thing holding things together
3:28 - while it rained, worked on the motor board...
3:36 - to get angle of motorboard "correct", made a small sample piece and tried the angle cut...the first angle was too steep so glad I did so (oursis slightly more vertical than the plans)
4:51 - I lose it trying to get "tee nuts" to line up with bolts...FIRST - clamp the nut with your vice grips, SECOND make sure somebody at HomeDepot did not switch 32 turn with 24 turn nuts. I got about 8 of 14 to take. I used plain old 1 1/2 inch stainless screws where the tee nuts failed...likely could have used all screws instead of tee nuts
5:29 - hacking off screw and bolt ends - screws cut flush - another strike against tee nuts in my book
6:19 - red handled kitchen scissors on bottom of boat - used for fiber-glassing...don't tell.
8:12 - put some sort of metal on your motorboard where the engine clamps - the scrap tin seen here covers some rather nasty gouges from the maiden voyage!
9:35 - after swamping - and almost sinking - the boat twice in the first two days, second guessing the choice to cut out the holes in the stringers, may fiberglass them in this winter.
Видео sea flea mini max timelapse build 2016 канала mocmrfitz
8 day build and test runs of a mini max with 9.9 Merc. somewhere in the Haliburton Highlands Ontario. Commentary with time tags below:
0:26 - had to replace switch on old table saw
0:58 - twisting together the bow to close the "gore" was a gruesome task - lots small passes removing material with circular saw
2:20 - about this point we realized nothing lined up the way it does in the plans...the stringers were too short!...PL premium 8X used to fill the gap...then lots of sanding/rasping
3:05 - also added a second transom pad between the stringers to ensure PL was not the only thing holding things together
3:28 - while it rained, worked on the motor board...
3:36 - to get angle of motorboard "correct", made a small sample piece and tried the angle cut...the first angle was too steep so glad I did so (oursis slightly more vertical than the plans)
4:51 - I lose it trying to get "tee nuts" to line up with bolts...FIRST - clamp the nut with your vice grips, SECOND make sure somebody at HomeDepot did not switch 32 turn with 24 turn nuts. I got about 8 of 14 to take. I used plain old 1 1/2 inch stainless screws where the tee nuts failed...likely could have used all screws instead of tee nuts
5:29 - hacking off screw and bolt ends - screws cut flush - another strike against tee nuts in my book
6:19 - red handled kitchen scissors on bottom of boat - used for fiber-glassing...don't tell.
8:12 - put some sort of metal on your motorboard where the engine clamps - the scrap tin seen here covers some rather nasty gouges from the maiden voyage!
9:35 - after swamping - and almost sinking - the boat twice in the first two days, second guessing the choice to cut out the holes in the stringers, may fiberglass them in this winter.
Видео sea flea mini max timelapse build 2016 канала mocmrfitz
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
Muskoka Seaflea - Fleafest 2012How To Build A Mini Max In Four HoursThunderball MiniMaxMIAMI BOAT BUILDHow To Fiberglass Over PlywoodMatthew Eidt - Building The Calgary Mini Max in 80 StepsVintage Hydro Built From Hal Kelly Boat Plans powered by a 1954 Mercury Mark 20My one sheet boat designWelcome to Captain Wulkie's GarageTime Lapse: i550 Sport Boat built with WEST SYSTEM EpoxyBuilding a Cocktail Class Racer from a CLC Kit15 Cool Mini Boats and Tiny Watercrafthow to build a boat from a doorHow to Build a Small Wooden Boat #14 Not Using Marine Plywood - Electric Powered Mini BoatHow To Build A Boat - TU-9 Tunnel Hull HDO'Connor Racing HydroplanesHow to build a JetBoat KitsetThe Mcphee Flea - A Scottish Mini Most AdventureAmazing Time Lapse Wooden Big Boat Build Process - Awesome DIY Project Wooden BoatHome Built Minimax Seaflea Test Run (2.5hp Yamaha Outboard)2017