Mercedes-Benz Actros | Removing the door module on an Actros
1,8,Before removing the door module on a new |Actros, remove the roller sun blind.||
9,15,This is installed on the driver side of the new |Actros as standard.||
19,22,No special tools are needed|for the removal.||
23,30,A tape measure is required for lowering |the window to a certain position.||
35,43,The window must protrude 20 - 30 cm|out of the door.||
44,49,Switch off the ignition and remove the key.|||
50,58,The Torx mounting screw for the door handle|on the door fold is equipped with a|safety plug.|
58,65,Pry out the plug with a screwdriver.|||
66,75,Remove the mounting screw for the|door handle.||
79,83,Press the door handle towards the|inside of the door by hand.||
84,89,The door handle is loose when it clicks.|||
90,96,Pull out the handle far enough so that the |linkage for the door lock is accessible.||
97,100,Unclip the linkage with a screwdriver.|||
101,104,Remove the door handle.|||
105,110,Remove the screw in the installation opening|of the door handle.||
111,118,Remove the three mounting screws|for the lock.||
119,125,Open the left-hand trim|in the driver footwell.||
126,129,The electrical connections for the door |electronics are behind this.||
130,136,Remove the three screws.|||
137,140,Unplug the cable strand which leads through|the rubber hose into the door.||
141,145,It has a green connector.|||
146,157,Detach the rubber hose and guide the cable|strand with connector through the opening|from the outside.|
160,162,Continue with the roller sun blind.|||
163,165,This is attached by four screws.|||
166,168,Start at the bottom on the right-hand rail.|||
169,174,Remove all protective caps from the screws.|||
182,185,Remove all four screws.|||
186,193,Also remove the rail.|||
201,207,The roller blind can be removed after the|upper bolts are removed.||
208,212,Remove the door trim from the window frame.|||
213,224,Remove two screws to do so.|||
226,236,Carefully remove the trim on the|window frame.||
239,246,Remove the entrance illumination|in the door.||
247,258,Using an assembly wedge,|remove the velour panel in the center |of the door trim.|
261,270,Remove the three highlighted screws of the|door module on the right-hand side.||
272,281,Remove the screw in the installation opening|of the entrance illumination.||
285,293,Remove the two highlighted screws of the|door module on the left-hand side.||
295,300,Ask an assistant for help|with holding the door module.||
301,306,Pull the cable with the green connector |on the right-hand side through the frame.||
307,311,Disconnect the last connector of the module.|||
312,325,Carefully pull out the door module from the|door frame fold and remove.||
326,328,Install in the reverse order.|||
329,331,Notes for installation:|||
332,338,When installing the door module,|insert the window into the window rail|on the left-hand side.|
339,342,Pay attention to the position of the cables|in the door module.||
343,347,The cables must not get caught in the|mechanical components of the power window.||
349,368,After installing the door handle,|press the safety plug which was removed |at the start back into the screw.|
370,380,Use a Torx screwdriver for this.|||
381,383,Normalize the power window.|||
384,391,Raise and lower the window several|times for this purpose.||
392,400,Once the roller sun blind has been installed |successfully, the repair is complete.||
Видео Mercedes-Benz Actros | Removing the door module on an Actros канала MBOwnersClub
9,15,This is installed on the driver side of the new |Actros as standard.||
19,22,No special tools are needed|for the removal.||
23,30,A tape measure is required for lowering |the window to a certain position.||
35,43,The window must protrude 20 - 30 cm|out of the door.||
44,49,Switch off the ignition and remove the key.|||
50,58,The Torx mounting screw for the door handle|on the door fold is equipped with a|safety plug.|
58,65,Pry out the plug with a screwdriver.|||
66,75,Remove the mounting screw for the|door handle.||
79,83,Press the door handle towards the|inside of the door by hand.||
84,89,The door handle is loose when it clicks.|||
90,96,Pull out the handle far enough so that the |linkage for the door lock is accessible.||
97,100,Unclip the linkage with a screwdriver.|||
101,104,Remove the door handle.|||
105,110,Remove the screw in the installation opening|of the door handle.||
111,118,Remove the three mounting screws|for the lock.||
119,125,Open the left-hand trim|in the driver footwell.||
126,129,The electrical connections for the door |electronics are behind this.||
130,136,Remove the three screws.|||
137,140,Unplug the cable strand which leads through|the rubber hose into the door.||
141,145,It has a green connector.|||
146,157,Detach the rubber hose and guide the cable|strand with connector through the opening|from the outside.|
160,162,Continue with the roller sun blind.|||
163,165,This is attached by four screws.|||
166,168,Start at the bottom on the right-hand rail.|||
169,174,Remove all protective caps from the screws.|||
182,185,Remove all four screws.|||
186,193,Also remove the rail.|||
201,207,The roller blind can be removed after the|upper bolts are removed.||
208,212,Remove the door trim from the window frame.|||
213,224,Remove two screws to do so.|||
226,236,Carefully remove the trim on the|window frame.||
239,246,Remove the entrance illumination|in the door.||
247,258,Using an assembly wedge,|remove the velour panel in the center |of the door trim.|
261,270,Remove the three highlighted screws of the|door module on the right-hand side.||
272,281,Remove the screw in the installation opening|of the entrance illumination.||
285,293,Remove the two highlighted screws of the|door module on the left-hand side.||
295,300,Ask an assistant for help|with holding the door module.||
301,306,Pull the cable with the green connector |on the right-hand side through the frame.||
307,311,Disconnect the last connector of the module.|||
312,325,Carefully pull out the door module from the|door frame fold and remove.||
326,328,Install in the reverse order.|||
329,331,Notes for installation:|||
332,338,When installing the door module,|insert the window into the window rail|on the left-hand side.|
339,342,Pay attention to the position of the cables|in the door module.||
343,347,The cables must not get caught in the|mechanical components of the power window.||
349,368,After installing the door handle,|press the safety plug which was removed |at the start back into the screw.|
370,380,Use a Torx screwdriver for this.|||
381,383,Normalize the power window.|||
384,391,Raise and lower the window several|times for this purpose.||
392,400,Once the roller sun blind has been installed |successfully, the repair is complete.||
Видео Mercedes-Benz Actros | Removing the door module on an Actros канала MBOwnersClub
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
Mercedes-Benz Actros Truck Production in GermanyThe power window on Mercedes-Benz ActrosСнятие стеклоподъёмника Mercedes Actros MP2 Window Regulator Replacementcomo desmonta da porta do actros (mercedes)Mercedes-Benz Actros - Removal / Installation of the front bumper | W930, W932, W933, W934Замена моторчика стеклоподъёмника Mercedes Actros MP 2Как снять торпедо на ACTROS Mercedes-BenzMercedes-Benz Actros - Replace the front cassette type sealing ring | W930, W932, W933, W934 (OM541)Mercedes-Benz Actros | LKW Telefon KomfortMercedes-Benz Actros | Replacing the gear sensorMercedes-Benz Actros Review Part 2Замена компрессора Mrcedes Actros MP1,MP2 Air Compressor ReplacementHow to title the cabin on a Mercedes Benz ActrosMercedes-Benz Actros | Bleed steering system in Actros MP IIMercedes-Benz Actros | Removal & Installation of the door module (defective control unit)Módulos de Controle do Vidro Elétrico - Mercedes Benz Actros 2546Mercedes Actros ProductionЗамена салонного радиатора Mercedes Actros MP2How to replace the front lights H7, H1, 21W, 4W bulbs replacement Mercedes Benz Actros MP4 DIYЗамена салонного моторчика Mercedes Actros MP2