08 Build Your Own Laser - Laser Tube Installation, Alignment & Water Protect

In this video I continue the Laser Build installing the Co2 Laser Tube, Water Flow Protection Switch, Align Mirrors, Install a beam combiner kit, and test laser and Trocen AWC-708S controller using LightBurn Software.

Stepper Motors, Stepper Drivers and More for your DIY Laser Build at -- https://www.omc-stepperonline.com//?tracking=5f7ce36148d79

The main components I am using for this build are from Cloudray Laser Visit them at https://www.cloudraylaser.com OR Cloudray’s AliExpress Store - http://s.click.aliexpress.com/e/p2mI2aPW

A PDF Wiring Guide for the DIY Laser is available here - https://mwlaser.com.au/product/ebook-matts-diy-laser-wiring-guide/

DISCLAIMER: The producer of this video under no circumstances can be found liable for negligence by a viewer if they are seriously injured, dies or suffers damage to their property after acting upon or using the content contained in this video production. Any person/s acting on information contained in this video do so at their own risk. The viewer also acknowledges they must follow all local and national laws and regulations when performing any work described in this video production. MAINS POWER CONNECTIONS MUST ONLY BE INSTALLED BY A LICENSED PROFESSIONAL.

If you'd like to support my channel financially so I can continue to produce content and provide support you can do that via PayPal here --- https://www.paypal.me/mattsworkshop --- Thank You

More Info and Product Information I Use for This Build Can be found on my Website - https://mwlaser.com.au/diy-laser-build/

The wiring ferrules and Crimping tools used in this build were from AliExpress - http://s.click.aliexpress.com/e/sqZVzTX6

Parts Featured in this video are:

Cloudray Co2 Laser Tube - http://s.click.aliexpress.com/e/rG8HORNm

Cloudray Laser Power Supply - http://s.click.aliexpress.com/e/4D1mRpky

Water Flow Sensor Switch - http://s.click.aliexpress.com/e/37Wbmul6

Red Mushroom Emergency Stop Button - http://s.click.aliexpress.com/e/EqAb97i0

TROCEN AWC708S Controller - http://s.click.aliexpress.com/e/noq4O7kM

S&A CW5200 / CW5202 Chiller - http://s.click.aliexpress.com/e/sW7Y2dOC

Cloudray Laser Lens & Mirrors - http://s.click.aliexpress.com/e/LcZLFQdE
The Wire I Used to hook up the electrical components was purchased from AliExpress it comes in a box of six colours - https://mwlaser.com.au/product/42m-box-hook-up-24awg-wire-6-colours/

Z-Axis Auto Focus Sensor / Limit Switch Pen - https://mwlaser.com.au/product/cloudray-auto-focus-focusing-sensor-z-axis/

Cloudray Analog Ammeter (Available in 0-30mA and 0-50mA) https://mwlaser.com.au/product/cloudray-30-50ma-ammeter/

The Mechanical parts I used for this Laser Build are from Cloudray - This set below is for the size I am building 1300x900mm cutting area. It comes with all mechanical components, laser lens head, mirror mounts, tube mounts stepper motor mounts, axis rails and timing belt.

http://s.click.aliexpress.com/e/CcVFEAla - Product - Cloudray Mechanical Parts Set 1300*900mm Inner Sliding Rails Kits Spare Parts for DIY 1390 CO2 Laser Engraving Cutting Machine

Thanks for Visiting.
Until next time, take care
Cheers Matthew
Visit Matt's Workshop at NEW WEBSITE: https://www.mwlaser.com.au
Instagram https://www.instagram.com/mattsworkshop/
Facebook https://www.facebook.com/mattsworkshopau
NOTE: This is not a paid production or advertisement. The featured products are provided by Cloudray to allow me to provide viewers with an installation / how-to video.

Видео 08 Build Your Own Laser - Laser Tube Installation, Alignment & Water Protect канала MW Laser