Hardtail Vise Ep. 22: Internal Shaping to Fit Dynamic Jaw
As we get to the final machining needed for our Hardtail vise, we'll get the inside area of the fixed jaw body machined to fit the dynamic jaw. For this I will be using the G&E shaper and a 12" long bar I made to cut the four corners that hold the dynamic jaw in the center. This was no simple task by any means but it was a great challenge to work on and I am excited to share this with everyone. I had well over two hours of video of this setup including the final fitment so I broke this into two final videos. The next video will show the completion of the Hardtail vise. #abom79 #metalshaper #hardtailvise #shaper #manualmachining
Paypal Channel Donation: https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=T325L5JZMY9LY&source=url
Support though Patreon: https://www.patreon.com/abom79
My Amazon store where I'm adding many of the tools and products I use in my own shop. Amazon.com/shop/abom79
Visit my second Youtube channel where you can follow our travels, camping, RVing, cooking, and bbq!
Видео Hardtail Vise Ep. 22: Internal Shaping to Fit Dynamic Jaw канала Abom79
Paypal Channel Donation: https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=T325L5JZMY9LY&source=url
Support though Patreon: https://www.patreon.com/abom79
My Amazon store where I'm adding many of the tools and products I use in my own shop. Amazon.com/shop/abom79
Visit my second Youtube channel where you can follow our travels, camping, RVing, cooking, and bbq!
Видео Hardtail Vise Ep. 22: Internal Shaping to Fit Dynamic Jaw канала Abom79
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
![Gear Modifications Part 2](https://i.ytimg.com/vi/dbwPhqAoxnw/default.jpg)
![Finishing the Compound Acme Lead Screw](https://i.ytimg.com/vi/vYT0VWNZhpE/default.jpg)
![New Shaft for Bull Gear, Long Workpiece Challenges](https://i.ytimg.com/vi/s7yleCPhxJI/default.jpg)
![Norton Power-feed Gearbox Repair Part 2: Machining the Braze](https://i.ytimg.com/vi/0gj27uWafLU/default.jpg)
![Monarch Lathe Clutch Repair Part 2](https://i.ytimg.com/vi/p7PNT53FmWA/default.jpg)
![WIYB Toolmakers Collaboration Machinist Vise Part 7 : Finale](https://i.ytimg.com/vi/ab29u05iNpM/default.jpg)
![Lead Screw Repair for 10" Rockwell Lathe](https://i.ytimg.com/vi/kR-6ZUhKuuE/default.jpg)
![Thermal Flame Spraying Centrifuge Shaft Repair](https://i.ytimg.com/vi/7pO7RUNSyRk/default.jpg)
![Lathe Clutch Shaft Repair Pt 2](https://i.ytimg.com/vi/L3EHLWNGNqo/default.jpg)
![AWS Back Purge Welding Fixture Part 8: Finale](https://i.ytimg.com/vi/ozO4OSS8S5Q/default.jpg)
![Lathe Spindle Repair](https://i.ytimg.com/vi/-IT28Qn4ark/default.jpg)
![WIYB Toolmakers Collaboration Machinist Vice Part 2](https://i.ytimg.com/vi/oVxsToKRjus/default.jpg)
![New Shop Space Going Up!](https://i.ytimg.com/vi/kMaSTrPFc0o/default.jpg)
![American Pacemaker Lathe Arrival & Unloading](https://i.ytimg.com/vi/98xVAWNBop0/default.jpg)
![Kubota Hydraulics Cylinders Part 3: Reassembly with New Seals and Rods](https://i.ytimg.com/vi/CmGjG--JSp8/default.jpg)
![Custom Aluminum Rod Ends](https://i.ytimg.com/vi/qVvBpdz_l7c/default.jpg)
![SNS 337 Part 2: Knuckle Boom Pin Boss Completed](https://i.ytimg.com/vi/ZC6cEG4RRTE/default.jpg)
![Mahindra Hydraulic Cylinders: Resealed and Reassembled](https://i.ytimg.com/vi/H_UL3srw_Kc/default.jpg)
![Lathe Clutch Shaft Repair Part 1](https://i.ytimg.com/vi/jgFTFYshnOY/default.jpg)
![Drive Rollers, Rush Job for the County](https://i.ytimg.com/vi/iIcHZAZZBWA/default.jpg)
![Fairbanks Power Hammer Cross Head Part 7: Finished!](https://i.ytimg.com/vi/epx4KXelAXY/default.jpg)