Arbor Support 6: Welding, Boring and Sawing the Slot
We made a lot of progress on our two arbor supports this time. As always there are a few bumps in the road. Getting good welds is tough enough, but sometimes you have complications like you'll see in this episode. In spite of that, we pushed along and the parts are closer and closer to getting complete.
Видео Arbor Support 6: Welding, Boring and Sawing the Slot канала Tillie's in a Bottle
Видео Arbor Support 6: Welding, Boring and Sawing the Slot канала Tillie's in a Bottle
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
![Making a Better Chuck key](https://i.ytimg.com/vi/tDl-pB_Vk1E/default.jpg)
![Greenerd No.3 Arbor Press](https://i.ytimg.com/vi/0jG6-j1pYO4/default.jpg)
![Making T Nuts for the Nichols Mill](https://i.ytimg.com/vi/1yPb6Qy5m98/default.jpg)
![Converting the Boice Crane Bandsaw for Cutting Metal , by the Jackshaft Method](https://i.ytimg.com/vi/8gy5XHz5Z4o/default.jpg)
![Blade Guide for the Boice Crane Bandsaw Part 1](https://i.ytimg.com/vi/qAlF5yfdiJ8/default.jpg)
![Arbor Support for the Nichols Mill Part 1](https://i.ytimg.com/vi/gz4hRefhUjo/default.jpg)
![Making a Table Nut for the Nichols Milling Machine Part 1](https://i.ytimg.com/vi/05mWKL_hets/default.jpg)
![What Size Should a Balancing Arbor Be For The Surface Grinder?](https://i.ytimg.com/vi/rAT8PTNH2zg/default.jpg)
![Making a Table Nut for the Nichols Milling Machine Part 2](https://i.ytimg.com/vi/93ZCkmM7FbM/default.jpg)
![Dressing and Inspecting the Magchuck on a Surface Grinder](https://i.ytimg.com/vi/BcoN9fZM9Ac/default.jpg)
![Fixing the Knee on the Nichols Mill](https://i.ytimg.com/vi/Auq8z2m3GCs/default.jpg)
![What Size of Stock do you Need to Make a Hexagon for your Wrench?](https://i.ytimg.com/vi/JPbtiwb5TmI/default.jpg)
![Arbor Support 3: Finishing the Welding Jig, Getting Accurate Results with an Inaccurate Machine...](https://i.ytimg.com/vi/_4XjRI-Irys/default.jpg)
![Sharing tooling between the mill and lathe](https://i.ytimg.com/vi/B3U4ZhrzaU8/default.jpg)
![Charlie bar](https://i.ytimg.com/vi/Ya_4TnombEM/default.jpg)
![Arbor Support 5: Ball-turning with an end mill, Toolmaker's buttons, and the Secret to Success....](https://i.ytimg.com/vi/Vsu5ceU1Ots/default.jpg)
![Lamp Clamp](https://i.ytimg.com/vi/_dfPXGCbiNY/default.jpg)
![Table Locks for the Nichols Mill](https://i.ytimg.com/vi/4JqvAhy2FwE/default.jpg)
![More Upgrades To The Mill: New Overarm, Oil Change, and Restoring the Electrical System](https://i.ytimg.com/vi/VM2s8Xw6kCM/default.jpg)
![Arbor Support 7: Cat 40 Drawbar, Switching the Motor and Shrink Fitting the Bearing Sleeve](https://i.ytimg.com/vi/u9ZuuBEGkR4/default.jpg)