Загрузка страницы
Все видеоНовые видеоПопулярные видеоКатегории видео

Ultra96 Quick Tutorial: How to load off of the SD Card!

*** MAKE SURE YOU HAVE THE BOOT SWITCHES SET CORRECTLY: 1 OFF and 2 ON ****

This video should serve as a quick tutorial or reference on how to boot the Ultra96 directly off of the SD Card. This video assumes you already have a HW design made in Vivado, if not see the previous video link below. In a few quick steps we make an FSBL with a board support package, add our program, create a boot image, and load the design to the Ultra96 Xilinx Zynq UltraScale+ MPSoC via the SD Card. Hope you enjoy the video and it serves as a good reference. Have a great day and don't forget to #LoveWell!!

Previous Video:
https://youtu.be/RAxLmHwIWH4

Drive an LED Video:
https://youtu.be/92KWwuTwNdI

https://www.patreon.com/JoshuaMacFie

Видео Ultra96 Quick Tutorial: How to load off of the SD Card! канала GEEK
Показать
Комментарии отсутствуют
Введите заголовок:

Введите адрес ссылки:

Введите адрес видео с YouTube:

Зарегистрируйтесь или войдите с
Информация о видео
2 августа 2020 г. 23:04:37
00:05:27
GEEK
Теги
Правообладателям
Жалоба
Комментарии
Другие видео канала
Drive an LED with an FPGA, Micro-controller, or any low power signal circuit!Drive an LED with an FPGA, Micro-controller, or any low power signal circuit!Seven Segment Verilog counter on the Basys2 board!Seven Segment Verilog counter on the Basys2 board!How to code verilog for an IR Sensor Tristate bufferHow to code verilog for an IR Sensor Tristate bufferUltra96, use Verilog program to write to an external pin (LED?) via FPGAUltra96, use Verilog program to write to an external pin (LED?) via FPGAHow to code verilog for a LCD part 4: Final concepts for LCD and wiring diagram.How to code verilog for a LCD part 4: Final concepts for LCD and wiring diagram.Board Spin-up! Basys2 FPGA: Downloading Digilent Adept and programming blinking LED.Board Spin-up! Basys2 FPGA: Downloading Digilent Adept and programming blinking LED.How to code Verilog for a servo! Using the basys2 FPGA board.How to code Verilog for a servo! Using the basys2 FPGA board.Ultra96, use a C program to write to an external pin (LED?) via onboard processors!Ultra96, use a C program to write to an external pin (LED?) via onboard processors!How to make an overcurrent circuit!How to make an overcurrent circuit!Seven Segment Display Bank Decoded and Explained!Seven Segment Display Bank Decoded and Explained!Hello World Ultra96! Build the base project on the Ultra96 with a Zynq Processor.Hello World Ultra96! Build the base project on the Ultra96 with a Zynq Processor.Verilog Processor Build Series part 2: Build a Function Unit (ALU and Shifter) our of Verilog!Verilog Processor Build Series part 2: Build a Function Unit (ALU and Shifter) our of Verilog!How to code verilog for ultrasonic distance sensing.How to code verilog for ultrasonic distance sensing.How to install Adept software from Digilent on Linux!How to install Adept software from Digilent on Linux!Board Spin-up! Ultra96 Zynq FPGA: Unboxing and running Linux!Board Spin-up! Ultra96 Zynq FPGA: Unboxing and running Linux!MPPT Buck converter circuit review.MPPT Buck converter circuit review.How to install Xilinx Vivado on Linux! 12 easy steps!How to install Xilinx Vivado on Linux! 12 easy steps!Verilog Processor Build Series part 1: Build a Function Unit (ALU and Shifter) our of Verilog!Verilog Processor Build Series part 1: Build a Function Unit (ALU and Shifter) our of Verilog!How to code verilog for a LCD part 2: Mojo FPGA and getting started blinking an LEDHow to code verilog for a LCD part 2: Mojo FPGA and getting started blinking an LEDHow to fix monitor speakers that have a hum.How to fix monitor speakers that have a hum.
Статистика портала
Яндекс.Метрика
© 2008-2024 «Информационно-развлекательный портал города Верхняя Салда»
| Карта портала | Реклама | Контакты | Сообщить об ошибке | Соглашения
salda.ws salda.ws@mail.ru
Сейчас на сайте: 512 Статистика портала