How to code verilog for a LCD part 2: Mojo FPGA and getting started blinking an LED
This is the second video in the series that covers programming an FPGA to output to a Liquid Crystal Display (LCD). This video covers the Mojo V3, turning on an LED programmatically and turning on an LED using a button. This will be a great series for starters since this is how I started. It will move through how to turn on a Light Emitting Diode via programming or a button, then how to repetitively change a bank of LED outputs. Then finally, how to sequence a bank of outputs that can be used to drive an LCD display. The progression of this series will ultimately show how to go from very basic to intermediate concepts. I have listed below links to the parts needed.
Mojo V3 FPGA: https://amzn.to/2J4pOIg
Male-to-male jumper wires: https://amzn.to/2wtAqOe
Tactile push-button: https://amzn.to/2UvE027
Resistor kit: https://amzn.to/2WweWeh
16x2 LCD: https://amzn.to/2WzGS0L
Potentiometers: https://amzn.to/3cYhEyX
Breadboard: https://amzn.to/3dnsKgY
(This breadboard is different from the original one. The original was terrible to work with, I would suggest this board instead.)
I'm not sure if the LCD needs any soldering but if so, I would recommend the Hakko that I use:
https://amzn.to/2UbUbD5
Here is the link to the video that shows the LCD working:
https://youtu.be/4A3yRNOK_sQ
Here is the link to the embedded micro website, looks to be under a new name but still good content:
https://alchitry.com/pages/verilog-fpga-tutorials
FPGA-LCD series videos
Part 1: https://youtu.be/EOSWNzyxDp4
Part 2: https://youtu.be/AuvAGUJmrPM
Part 3: https://youtu.be/mbiiLqUGS2w
Part 4: https://youtu.be/3w_0RAFUjAM
Full FPGA, LCD, Temperature code:
https://github.com/josh-macfie/FPGAtoLCD/blob/master/display.v
https://www.patreon.com/JoshuaMacFie
Видео How to code verilog for a LCD part 2: Mojo FPGA and getting started blinking an LED канала GEEK
Mojo V3 FPGA: https://amzn.to/2J4pOIg
Male-to-male jumper wires: https://amzn.to/2wtAqOe
Tactile push-button: https://amzn.to/2UvE027
Resistor kit: https://amzn.to/2WweWeh
16x2 LCD: https://amzn.to/2WzGS0L
Potentiometers: https://amzn.to/3cYhEyX
Breadboard: https://amzn.to/3dnsKgY
(This breadboard is different from the original one. The original was terrible to work with, I would suggest this board instead.)
I'm not sure if the LCD needs any soldering but if so, I would recommend the Hakko that I use:
https://amzn.to/2UbUbD5
Here is the link to the video that shows the LCD working:
https://youtu.be/4A3yRNOK_sQ
Here is the link to the embedded micro website, looks to be under a new name but still good content:
https://alchitry.com/pages/verilog-fpga-tutorials
FPGA-LCD series videos
Part 1: https://youtu.be/EOSWNzyxDp4
Part 2: https://youtu.be/AuvAGUJmrPM
Part 3: https://youtu.be/mbiiLqUGS2w
Part 4: https://youtu.be/3w_0RAFUjAM
Full FPGA, LCD, Temperature code:
https://github.com/josh-macfie/FPGAtoLCD/blob/master/display.v
https://www.patreon.com/JoshuaMacFie
Видео How to code verilog for a LCD part 2: Mojo FPGA and getting started blinking an LED канала GEEK
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
Drive an LED with an FPGA, Micro-controller, or any low power signal circuit!Seven Segment Verilog counter on the Basys2 board!How to code verilog for an IR Sensor Tristate bufferUltra96, use Verilog program to write to an external pin (LED?) via FPGAHow to code verilog for a LCD part 4: Final concepts for LCD and wiring diagram.Ultra96 Quick Tutorial: How to load off of the SD Card!Board Spin-up! Basys2 FPGA: Downloading Digilent Adept and programming blinking LED.How to code Verilog for a servo! Using the basys2 FPGA board.Ultra96, use a C program to write to an external pin (LED?) via onboard processors!How to make an overcurrent circuit!Seven Segment Display Bank Decoded and Explained!Hello World Ultra96! Build the base project on the Ultra96 with a Zynq Processor.Verilog Processor Build Series part 2: Build a Function Unit (ALU and Shifter) our of Verilog!How to code verilog for ultrasonic distance sensing.How to install Adept software from Digilent on Linux!Board Spin-up! Ultra96 Zynq FPGA: Unboxing and running Linux!MPPT Buck converter circuit review.How to install Xilinx Vivado on Linux! 12 easy steps!Verilog Processor Build Series part 1: Build a Function Unit (ALU and Shifter) our of Verilog!How to fix monitor speakers that have a hum.