Floor board replacement
This took a while. I'm no expert, so I didnwhat any newb does and dove right in. Turned out OK. I wish I was a better welder.
New metal from BJ's. Requires quite a bit of fitting and instill didn't get it just right, but it's better.
I used weld through primer everywhere. after welding and smoothing, I used a lot of Rust Bullet on all the seams.
Next up is taking the rest of the tar off, grinding and epoxy.
Let me know, should I Raptor the floor, or paint it?
Видео Floor board replacement канала Comfort in Discomfort
New metal from BJ's. Requires quite a bit of fitting and instill didn't get it just right, but it's better.
I used weld through primer everywhere. after welding and smoothing, I used a lot of Rust Bullet on all the seams.
Next up is taking the rest of the tar off, grinding and epoxy.
Let me know, should I Raptor the floor, or paint it?
Видео Floor board replacement канала Comfort in Discomfort
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
![Tearing down the driver's door Part 1](https://i.ytimg.com/vi/lQnGSr_NOt4/default.jpg)
![Spraying Nason Epoxy on the Wagoneer](https://i.ytimg.com/vi/0x-6-hGCU7E/default.jpg)
![Nason Epoxy on the Wag.](https://i.ytimg.com/vi/SEYkPLWdp34/default.jpg)
![Grand Wagoneer Seat Swap - Complete!!](https://i.ytimg.com/vi/lb-715guj9I/default.jpg)
![Sanding, Sanding, and more sanding](https://i.ytimg.com/vi/CbWZo8WCBSs/default.jpg)
![Removing Wagoneer Windshield](https://i.ytimg.com/vi/1r3ezEdu-CY/default.jpg)
![Sheet metal patch weld - OK mainly](https://i.ytimg.com/vi/Iy7qee2fGwQ/default.jpg)
![Grand Cherokee seat switch](https://i.ytimg.com/vi/rZfsr23yPt0/default.jpg)
![Wagoneer Door Refinishing part 2](https://i.ytimg.com/vi/X564UL07BZI/default.jpg)
![Eastwood SCT Contour vs. Old paint](https://i.ytimg.com/vi/XhENadzQzhk/default.jpg)
![Follow-up for Adam - Swivel](https://i.ytimg.com/vi/PBK6F1xcCu0/default.jpg)
![Prep for Tintable Raptor Liner.](https://i.ytimg.com/vi/Dt2EGY8dbDg/default.jpg)
![Removing Grand Wagoneer roof rack](https://i.ytimg.com/vi/w71rwNF7X2E/default.jpg)
![Removing Grand Wagoneer Tail Lamps](https://i.ytimg.com/vi/BXc52bo70k0/default.jpg)
![Pressing bushings](https://i.ytimg.com/vi/_ccxFzx4XoM/default.jpg)
![All about hinge pins - FSJ Wagoneer](https://i.ytimg.com/vi/oWiyt-W0_Ws/default.jpg)
![Jeep JK key upgrade (DIY Cutting)](https://i.ytimg.com/vi/2XRs4A0PXKw/default.jpg)
![Warn 9.5ti Winch Part 7 POR-15](https://i.ytimg.com/vi/7BpcCs0EYcA/default.jpg)
![Start of 1986 Grand Wagoneer project](https://i.ytimg.com/vi/i19DBii4jGA/default.jpg)
![Spraying Tintable Raptor on the floor.](https://i.ytimg.com/vi/nhwu6-9lROc/default.jpg)
![Wet Sandblasting at home - Dustless?](https://i.ytimg.com/vi/KrlUYayCEL0/default.jpg)