How To Read VSC Codes Toyota Sequoia Tundra 2001-2007 Stability Control ABS
If you want to a good solid ABS/OBD scanner, here is a solid inexpensive one. This will enable you to read and delete codes.
https://amzn.to/3a7A0LR
In this video I will show you how to read the code on your VSC light without an expensive scanner. Here are some instructions:
There are 3 pins on the OBDII connector you will use, Ts, Tc, and CG.
The pins are arranged like:
......__......
XXXXXXXX
XXXXXXXX
The underscore show the alignment tab. The pins are located here
Ts = 1
Tc = 2
CG = 3
.....__.....
XX12XXXX
XXXX3XXX
To check code
1. Short Tc and CG
2. Start engine
3. VSC will blink code(s) in order with a space between.
4. If it is flashing evenly and rapidly there is no code.
5. turn off, remove jumper
To clear code (you can't do it by disconnecting battery or with code reader)
1. Short Tc and CG
2. Start engine
3. Press brake pedal 8 times within 5 seconds
4. codes are clear, turn off and remove jumper.
Zero point Calibration ZPC
1. Center steering wheel
2. Short Ts and CG
3. Start engine and wait 4 sec
4. move steering wheel more than 5 deg and then re-center.
5. quickly press TRAC OFF button 3 times (within 3 sec)
6. long beep = success ZPC complete
7. turn off remove jumper
CODE DEFINITIONS:
Codes shown by ABS light
71 low volt right front
72 """ " left front
73 Low volt right rear
74 low volt left rear
75 abnormal change rf
76 abnormal chg lf
77 abnormal chg rr
78 abnormal chg lr
79 Deceleration sensor faulty
81 Master cyl press sensor bad
Codes shown by VSC TRAC
71 Yaw rate sens malfunc
72 Steering pos sens malfunc
Codes from ABS light
31 rf spd sens malf
32 lf spd sens malf
33 rr spd sens malf
34 lr spd sens malf
21 Malf ABS and VSC solenoid valves
11 Open or short circ ABS VSC relay circ
41 Low/High battery voltage
49 Open circ stop light sw
51 Pump mtr locked
37 Different tire size(s)
48 Center diff lock circ malf
ABS always ON is skid control ECU problem
Codes from VSC TRAC light
53 ECM communication malf
43 ABS control malf
31 Steering angle sens malf
32 Decel sens malf
34 Yaw rate sens malf
11 Open or short in brake booster circ
12 Open or short in brake inhibit relay circ
61 Master cyl press sens malf
62 Abnormal battery voltage VSC sensor
36 Malf in sensor set value (VSC sens system)
63 Malf in booster pedal force switch
If you like receiving free stocks, use my referral link to receive 3 free stock!
https://act.webull.com/on/watr7OvvhvMw/rnv/inviteUs/
One when you open account, and two when you successfully deposit $100.00! WeBull is a great trading platform with ZERO commission fees. By doing this you are helping support my channel. Thanks guys!
Thanks for looking and comment if you have any questions!
Here are some of the things I use daily when working on cars:
https://amzn.to/3dl0hbV --- OBD II Scanner
https://amzn.to/2U4HgCR --- Oil Life Reset Tool
https://amzn.to/2U3q00A --- Microfiber Towels
https://amzn.to/2vEiOPi --- Heavy Duty Jumper Pack
https://amzn.to/3ba97Hq --- Pocket Sized Jumper Pack
https://amzn.to/3ddFE12 --- 12v Battery Charger
Видео How To Read VSC Codes Toyota Sequoia Tundra 2001-2007 Stability Control ABS канала Karrs Kars
https://amzn.to/3a7A0LR
In this video I will show you how to read the code on your VSC light without an expensive scanner. Here are some instructions:
There are 3 pins on the OBDII connector you will use, Ts, Tc, and CG.
The pins are arranged like:
......__......
XXXXXXXX
XXXXXXXX
The underscore show the alignment tab. The pins are located here
Ts = 1
Tc = 2
CG = 3
.....__.....
XX12XXXX
XXXX3XXX
To check code
1. Short Tc and CG
2. Start engine
3. VSC will blink code(s) in order with a space between.
4. If it is flashing evenly and rapidly there is no code.
5. turn off, remove jumper
To clear code (you can't do it by disconnecting battery or with code reader)
1. Short Tc and CG
2. Start engine
3. Press brake pedal 8 times within 5 seconds
4. codes are clear, turn off and remove jumper.
Zero point Calibration ZPC
1. Center steering wheel
2. Short Ts and CG
3. Start engine and wait 4 sec
4. move steering wheel more than 5 deg and then re-center.
5. quickly press TRAC OFF button 3 times (within 3 sec)
6. long beep = success ZPC complete
7. turn off remove jumper
CODE DEFINITIONS:
Codes shown by ABS light
71 low volt right front
72 """ " left front
73 Low volt right rear
74 low volt left rear
75 abnormal change rf
76 abnormal chg lf
77 abnormal chg rr
78 abnormal chg lr
79 Deceleration sensor faulty
81 Master cyl press sensor bad
Codes shown by VSC TRAC
71 Yaw rate sens malfunc
72 Steering pos sens malfunc
Codes from ABS light
31 rf spd sens malf
32 lf spd sens malf
33 rr spd sens malf
34 lr spd sens malf
21 Malf ABS and VSC solenoid valves
11 Open or short circ ABS VSC relay circ
41 Low/High battery voltage
49 Open circ stop light sw
51 Pump mtr locked
37 Different tire size(s)
48 Center diff lock circ malf
ABS always ON is skid control ECU problem
Codes from VSC TRAC light
53 ECM communication malf
43 ABS control malf
31 Steering angle sens malf
32 Decel sens malf
34 Yaw rate sens malf
11 Open or short in brake booster circ
12 Open or short in brake inhibit relay circ
61 Master cyl press sens malf
62 Abnormal battery voltage VSC sensor
36 Malf in sensor set value (VSC sens system)
63 Malf in booster pedal force switch
If you like receiving free stocks, use my referral link to receive 3 free stock!
https://act.webull.com/on/watr7OvvhvMw/rnv/inviteUs/
One when you open account, and two when you successfully deposit $100.00! WeBull is a great trading platform with ZERO commission fees. By doing this you are helping support my channel. Thanks guys!
Thanks for looking and comment if you have any questions!
Here are some of the things I use daily when working on cars:
https://amzn.to/3dl0hbV --- OBD II Scanner
https://amzn.to/2U4HgCR --- Oil Life Reset Tool
https://amzn.to/2U3q00A --- Microfiber Towels
https://amzn.to/2vEiOPi --- Heavy Duty Jumper Pack
https://amzn.to/3ba97Hq --- Pocket Sized Jumper Pack
https://amzn.to/3ddFE12 --- 12v Battery Charger
Видео How To Read VSC Codes Toyota Sequoia Tundra 2001-2007 Stability Control ABS канала Karrs Kars
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
(Part 4) How To Fix Your Check Engine, VSC, Trac Off Warning Lights With Zero Point CalibrationDiagnosing the VSC OFF, VSC TRAC & CEL lights on a Toyota Sequoia 1st GenLUCES DE TRACCION PROVOCADAS POR UN MISFIREHow to fix ABS light, Traction Control, StabilitrakWhat to look for when buying a sequoia: 2001-2007⭐ 2002 Toyota Sequoia - P0440 - P0441 - P0446 - EVAP System Or Purge MalfunctionCheck Engine Light VSC TRAC Fix For Lexus GX470 GX 470 Easy Fix Repair Common to Toyota alsoCómo apagar luces de tracción VSC y VSC OFF fijas en el cuadro, TOYOTA & LEXUS.Here's Why the Toyota Sequoia is the Best SUV to Buy Right NowTop 5 Problems Toyota Sequoia SUV 1st Generation 2001-07Toyota Sequoia / Tundra Front ABS Wheel Speed Sensor replacement(Part 2) How To Fix Your Check Engine, VSC, Trac Off Warning Lights00-07 Toyota Sequoia/Tundra Turn Traction control off.Toyota ABS VCS Easy Wierd Fix P0420Faulty VSC IN 2001 Toyota Sequoia - brakes + ABS engage going 70 mphHow to turn Toyota's Vcs and other lights off!!!Big Problem owning Toyota Sequoiasequoia 4wd troubleshooting(Part 1) How To Fix Your Check Engine, VSC, Trac Off Warning Lights OnTHIS Is The Most Underappreciated SUV, Because It's Named After A Tree Nobody Can Spell!