Using Smaart V8 to phase align subs to mains
In this video I show you how to time / phase align subwoofers with a line array using Rational Acoustics Smaart V8.
This was done with a quite old Roland M400 digital mixer with RIAC stage boxes. The sound system was two (2 x 3) stacks of QSC KLA12 line arrays, and was shaded +3 on the top box, +/-0 on the middle box, and -3 on the bottom box.
The subs were QSC KW181's.
The limitations I had to work around, was the polarity of the entire system measured reversed... and I had no polarity options on the mains or the subs.
In addition, there was no delay control without inserting a delay rack effects, and using that to adjust delay. And because it was a rack delay, my adjustments in time was .8 ms, rather than a more fine tuned .3 or better.
So if you notice on my sub / main alignment, my crossover point was 180° out of phase. But because everything in the entire system has this same behavior, it wasn't really an issue.
And Easter egg... I also said called stage left stage right. (Newb) lol
In the future I'll do this video again using a Behringer X32, or the Midas M32 which at the moment are my favorite consoles.
Видео Using Smaart V8 to phase align subs to mains канала Donovan Cline
This was done with a quite old Roland M400 digital mixer with RIAC stage boxes. The sound system was two (2 x 3) stacks of QSC KLA12 line arrays, and was shaded +3 on the top box, +/-0 on the middle box, and -3 on the bottom box.
The subs were QSC KW181's.
The limitations I had to work around, was the polarity of the entire system measured reversed... and I had no polarity options on the mains or the subs.
In addition, there was no delay control without inserting a delay rack effects, and using that to adjust delay. And because it was a rack delay, my adjustments in time was .8 ms, rather than a more fine tuned .3 or better.
So if you notice on my sub / main alignment, my crossover point was 180° out of phase. But because everything in the entire system has this same behavior, it wasn't really an issue.
And Easter egg... I also said called stage left stage right. (Newb) lol
In the future I'll do this video again using a Behringer X32, or the Midas M32 which at the moment are my favorite consoles.
Видео Using Smaart V8 to phase align subs to mains канала Donovan Cline
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
Smaart - sub woofer alignment with Keith MorrisHow to route Smaart V8 to any mixer using a Digital I/O Interface + RTA & Transfer FunctionLinkin Park "The Hunting Party" Tour 2014 • Front of House Ken „Pooch“ Van Druten about the SoundUsing Pink Noise and the Built-In RTA to Ring Out Your RoomTUTORIAL SMAART - 15. CÁLCULO de un RETARDO de tres maneras - FIND, PHASE AS DELAY y UNWRAP PHASEsub + top finalTime aligning speakers using Smaart and a Behringer X32Using Smaart to EQ a room on a Behringer X32How to phase align main+sub in Smaart® [GSwSST34.1][Smaart v8 Basics] Part 1-Initial ConfigurationSmaart v8 Operation: 15 - Transfer Function Measurements and Delay ControlsSound System Tuning Step-by-Step using TRACT and SmaartLive Sound Phase Alignment with the InPhase PluginTECH: LIVE SOUND SUBS SUBWOOFER PLACEMENT & CONFIGURATION - LR, Center, Line, Cardioid, End FirePhase alignment exampleHow to calibrate a RTA mic to 94dB in SmaartHow to set the delay locator to measure a subwoofer in Smaart [GSwSST29]Phase Align Parallel Sources Using Rational Acoustics SMARRTTUTORIAL SMAART - 22. Aprender a medir y leer la FASE DE UN ALTAVOZ en una MEDICIÓN ACÚSTICASmaart Basics: Example System Overview