F650 Aimdroix Flamewheel with TopXGun Flight Controller *** No Longer Available ***

DJI F650 Aimdroix Flamewheel *** No Longer Available ***

Bind it with your Taranis radio and connect a 4S LiPo XT-60 connector battery and off you go. This build has only been flown a few times for different gains settings testing. This multirotor is stable and predictable. With its autonomous flight capabilites, this F650 can serve well as a small area mapping aircraft with a GoPro on time-lapse and 10000 mAh 4S LiPo pack.

Build Specifications:

OEM DJI F550 frame plates
Aimdroix V2 Aluminum Arms
SunnySky X2814 KV900
Velotech 30A ESC
TopXGun T1 Flight Controller
TopXGun 900 Mhz Data Link
FrSy X6R Receiver
APC 1245MR Props
FsSky FLVSS Lipo Voltage Sensor
FrSky FAS-100 Amp Sensor
FrSky Sensor w/ Smart Port
Landing Skids

The video shows a Zenmuse mount with a Feiyu Tech Mini 3D Gimbal during testing to have a sense of its aerial presence. Although it can certainly be used for aerial photography, this was not built for that purpose. The mount and gimbal are not included.

Buyer pays shipping. I'd be willing to partially disassemble it to put it a smaller box to help save on shipping cost. Other than that, I'll take it to a shipping vendor that will professionally pack it. I will send you the vendor's contact info so you can specify how you want it shipped and pay them directly.

Manufacturers' descriptions of the products used in this build:

TopXGun T1 flight controller (www.topxgun.com/en/T1) has been specifically designed for commercial and industrial multi-rotor UAV platforms. It is suitable for quad, hex and octo configurations and it features advanced functionality and safety protocols that make it ideal for serious UAV users. Besides supporting a wide range of multirotor platforms it also supports SBUS, PPM and PWM and with improved GPS position lock. This flight controller is accurate to 1.5m horizontally and 0.8m vertically. Flight missions are programmable with up to 128 waypoints possible and with a "point to go" function. You can direct the flight of your UAV platform straight from your smart phone or device. There are also 8 built in flight functions, including stable mode, GPS mode, intelligent orientation mode, skyway flight mode, click and fly mode, smart circle mode, failsafe mode (return to home) and low voltage protection.

Features:
• Built-in damping
• Supports nine types of multirotor platform quads hex and octocopter
• Supports SBUS, PPM and PWM receivers
• Sophisticated orientation control algorithm makes control easy
• Accurate GPS position lock
• Stronger immunity to magnetic field interference
• Failsafe - loss of signal return to home function
• Low battery alert and protection system
• Hexa-rotor protection for single motor failure
• Point to Go function - Change destination on mobile device/tablet
• Flight Missions Programmable by PC ground station or smart phone with up to 128 waypoints
• 8 Flight modes

TopXGun 900 Mhz Data Link (www.topxgun.com/en/DT) for long range FPV applications. The Data-Link has a range out to 2.5Km and comes with an air unit and a ground unit. The air unit is simply connected to the COM port on the TopXGun flight controller and the system is completed by simply connecting the ground unit to a computer or an OTG equipped iPad or Android tablet via a USB cable.

OEM DJI F550 frame plates. The optimized AIMDROIX V2 Aluminum Arms improves the performance of the multirotor while giving it a professional and rugged look. Because of the extended length, it adds 100mm in diameter to the multirotor, improving your flight stability.

SunnySky X2814 KV900 brushless motors are made of quality components that are normally only seen in high end products, and are designed to give years of high performance. Every motor has been carefully balanced and tested in the factory.

Velotech 30A ESC are featured with high efficiency, all N-channel MOSFET design, jitter-free hardware PWM input, and the most popular SimonK program, Velotech Magic speed controllers are an ideal choice for multirotors. Quality electronic parts are used to build Velotech Magic speed controllers, such as genuine Japanese Rubycon capacitor, IOR MOS tubes, heavy duty PCB. These parts cost much more than those cheaper counterparts that are frequently found in low price ESCs. The manufacturing process was strictly controlled and monitored to ensure all electronic parts are properly soldered. Every single ESC was examined in the factory with oscilloscope and other equipment, as well as burn-in test.

Видео F650 Aimdroix Flamewheel with TopXGun Flight Controller *** No Longer Available *** канала Flip on Tech