Setup of CW-5200 Water Chiller Unit for CNC Co2 Laser Machine - S&A From Cloudray Laser
This video is on the unboxing and setup of an S&A Water chiller CW-5200, This is one of the necessary upgrades to my current laser setup in my workshop as you may have seen I have been using a primitive method of cooling the laser and that needed to be improved.
I Use both the CW5200 and a CW5202 Chiller in my Workshop.
CW5200/5202 Chiller - https://mwlaser.com.au/product/cw5200-sa/
Lightobject LSR-EP4 CO2 Laser Eyes Protection Glasses/Goggle, 10600 nanometer - https://amzn.to/2l7bZzZ
Cloudray Laser https://www.cloudraylaser.com
https://www.facebook.com/cloudray.laser
This model the CW-5200 water chiller is a refrigeration type unit and is capable of maintaining the temperature to +/- 3 degrees from the set temperature.
TEYU S&A Industrial Water Chiller - http://s.click.aliexpress.com/e/_Bf6Eg9O0
Cloudray S&A CW5200 CW5202 Industry Air Water Chiller for CO2 Laser Engraving Cutting Machine Cooling
http://s.click.aliexpress.com/e/_Bf6Eg9O0
(0:39) Let’s unpack, and get going.
(1:45) After filling the water reservoir, I add a couple of capfuls of bleach to the water to help prevent algae and bacteria growth in the water system.
Using distilled water alone does not prevent the growth of bacteria in the laser tube and hoses, as the water system is not a sterile and sealed system.
During manufacturing the laser tube and system is tested prior to shipping with water that is not sterile, and the hoses also are hot sent in sterile packaging.
I ran a few capfuls of bleach in the last cooling arrangement I had and the water stayed crystal clear for approx 2 months, after which I replaced it with fresh water and again a few capfuls of bleach.
(2:36 Quick look at the thermostat parameters list
The default setting for the temperature control is set to “intelligent” in my case I will need to change that to “constant” for cooling the laser.
Intelligent mode - will cool the water to 3 degrees below the current room temperature, this may be OK for some applications of this chiller but, In the case of my workshop where temperatures regularly reach over 35 degrees on a good day, this would mean that the water cooling would maintain the temperature also in the 30 plus degree range which is Not really the best for the laser.
The constant temperature mode - is basically that, I can select a temperature that I want the water to be maintained at and then set.
The control panel is the same for CW-5000 and CW-5200
(5:22) Factory Settings Reset
(5:50) Entering The Thermostat Control Parameters - Press and Hold and UP and SET button together and Hold
(6:07) Entering Password = 8
(6:21) Thermostat Parameters
Changing From Intelligent to Constant Temperature Mode = F3
Changing Minimum Allowed Temperature = F9
Changing the Temperature Setting = F0
Press The RST within 20 Seconds or the settings will not be saved.
(7:51) Water Flow Alarm Demonstration on the Water Chiller.
(8:28) Thanks For visiting Matt’s workshop. If you haven't already hit the subscribe button and turn on the notification bell to be notified when I release a new video.
Until next time, take care
Cheers Matthew
Visit Matt's Workshop at https://www.mwlaser.com.au
Instagram https://www.instagram.com/mattsworkshop_mwlaser
Facebook https://www.facebook.com/mattsworkshopau
== If you'd like to support my channel financially so I can continue to produce content you can do via PayPal here --- https://www.paypal.me/mattsworkshop --- Thank You ====
Any questions please feel free to email me matt@mwlaser.com.au or leave a comment below.
NOTE: This is not a paid production or advertisement. The featured product was provided by Cloudray to allow me to provide viewers with an installation / how-to video.
English version of the Manual for the CW-5000 and CW-5200
https://drive.google.com/open?id=1Juyq0nR_PRnTkqxAqob-sJq1pRMDQFk2
Cloudray Laser https://www.cloudraylaser.com
https://www.facebook.com/cloudray.laser
Видео Setup of CW-5200 Water Chiller Unit for CNC Co2 Laser Machine - S&A From Cloudray Laser канала MW Laser
I Use both the CW5200 and a CW5202 Chiller in my Workshop.
CW5200/5202 Chiller - https://mwlaser.com.au/product/cw5200-sa/
Lightobject LSR-EP4 CO2 Laser Eyes Protection Glasses/Goggle, 10600 nanometer - https://amzn.to/2l7bZzZ
Cloudray Laser https://www.cloudraylaser.com
https://www.facebook.com/cloudray.laser
This model the CW-5200 water chiller is a refrigeration type unit and is capable of maintaining the temperature to +/- 3 degrees from the set temperature.
TEYU S&A Industrial Water Chiller - http://s.click.aliexpress.com/e/_Bf6Eg9O0
Cloudray S&A CW5200 CW5202 Industry Air Water Chiller for CO2 Laser Engraving Cutting Machine Cooling
http://s.click.aliexpress.com/e/_Bf6Eg9O0
(0:39) Let’s unpack, and get going.
(1:45) After filling the water reservoir, I add a couple of capfuls of bleach to the water to help prevent algae and bacteria growth in the water system.
Using distilled water alone does not prevent the growth of bacteria in the laser tube and hoses, as the water system is not a sterile and sealed system.
During manufacturing the laser tube and system is tested prior to shipping with water that is not sterile, and the hoses also are hot sent in sterile packaging.
I ran a few capfuls of bleach in the last cooling arrangement I had and the water stayed crystal clear for approx 2 months, after which I replaced it with fresh water and again a few capfuls of bleach.
(2:36 Quick look at the thermostat parameters list
The default setting for the temperature control is set to “intelligent” in my case I will need to change that to “constant” for cooling the laser.
Intelligent mode - will cool the water to 3 degrees below the current room temperature, this may be OK for some applications of this chiller but, In the case of my workshop where temperatures regularly reach over 35 degrees on a good day, this would mean that the water cooling would maintain the temperature also in the 30 plus degree range which is Not really the best for the laser.
The constant temperature mode - is basically that, I can select a temperature that I want the water to be maintained at and then set.
The control panel is the same for CW-5000 and CW-5200
(5:22) Factory Settings Reset
(5:50) Entering The Thermostat Control Parameters - Press and Hold and UP and SET button together and Hold
(6:07) Entering Password = 8
(6:21) Thermostat Parameters
Changing From Intelligent to Constant Temperature Mode = F3
Changing Minimum Allowed Temperature = F9
Changing the Temperature Setting = F0
Press The RST within 20 Seconds or the settings will not be saved.
(7:51) Water Flow Alarm Demonstration on the Water Chiller.
(8:28) Thanks For visiting Matt’s workshop. If you haven't already hit the subscribe button and turn on the notification bell to be notified when I release a new video.
Until next time, take care
Cheers Matthew
Visit Matt's Workshop at https://www.mwlaser.com.au
Instagram https://www.instagram.com/mattsworkshop_mwlaser
Facebook https://www.facebook.com/mattsworkshopau
== If you'd like to support my channel financially so I can continue to produce content you can do via PayPal here --- https://www.paypal.me/mattsworkshop --- Thank You ====
Any questions please feel free to email me matt@mwlaser.com.au or leave a comment below.
NOTE: This is not a paid production or advertisement. The featured product was provided by Cloudray to allow me to provide viewers with an installation / how-to video.
English version of the Manual for the CW-5000 and CW-5200
https://drive.google.com/open?id=1Juyq0nR_PRnTkqxAqob-sJq1pRMDQFk2
Cloudray Laser https://www.cloudraylaser.com
https://www.facebook.com/cloudray.laser
Видео Setup of CW-5200 Water Chiller Unit for CNC Co2 Laser Machine - S&A From Cloudray Laser канала MW Laser
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
Installing A Water Chiller In A Laser Engraver Cutter CW-5000/CW-5200CW S&A Water 5000/5200 chiller60 Watt CO2 Laser Unboxing and Initial SetupS & A CW5200 installation and setupBoss Laser Mirrors Alignment InstructionsCO2 Laser Alignment and How to Clean Laser Lens and Mirrors / Beginner Series Ep. 5B&H CW-5200 CHILLER REVIEW & TEMPERATURE SETTINGSSelecting Intelligent or Constant Mode on CW-5000 series ChillersHow to setup and use a laser cutter with RD WorksCo2 Laser Focus, Power & Speed Settings - Laser Ramp Test for CNC Co2 Laser MachinesLASER REVIEW - Future Upgrades & Mods of Chinese Red & Black CNC Co2 Laser Machine off eBay - 80WUpgraded Air Assist for Chinese | OM Tech CO2 LasermA - MILLIAMP METER INSTALL - CNC Co2 Laser Engraving / Cutting Machine - How to install ammeterChanging settings on CW-5000/CW-5200 ChillerLaser Cutter Mirror AlignmentTool time Tuesday Homend water chiller for C02 lasersHow to clean the dust on the gap of condensator for chiller CW-5000Industrial chiller 5200 Settings EnglishChiller Basics - How they workEp. 2 - LASER ROTARY ATTACHMENTS - Chuck Rotary Axis - Configuration, Settings - CNC Rotary Axis