#276 SG3525A / SG1525A / SG2525A Pulse Width Modulation PWM / SMPS Controller
Watch in Urdu Hindi https://youtu.be/Xtw-gTp36uQ
i explained SG3525A / SG1525A / SG2525A Pulse Width Modulator Controller functional description, pinout, circuit diagram and test circuit
The SG3525A, SG3527A pulse width modulator control circuits offer
improved performance and lower external parts count when implemented for controlling all types of switching power supplies i,e. buck converter, forward converter, half bridge, full bridge, push pull, boost converter, buck boost converter, continuous or discontinuous mode flyback SMPS. its on–chip +5.1 V reference is trimmed to ±1% and the error amplifier has an input common–mode voltage range that includes the reference voltage, thus eliminating the need for external divider resistors. A sync input to the oscillator enables multiple units to be slaved or a single unit to be synchronized to an external system clock. A wide range of dead-time can be programmed by a single resistor connected between the CT and Discharge pins. These devices also feature built–in soft–start circuitry, requiring only an external timing capacitor. A shutdown pin controls both the soft–start circuitry and the output stages, providing instantaneous turn off through the PWM latch with pulsed shutdown, as well as soft–start recycle with longer shutdown commands. The under voltage lockout inhibits the outputs and the changing of the soft–start capacitor when VCC is below nominal. The output stages are totem–pole design capable of sinking and sourcing in excess of 200 mA. The output stage of the SG3525A features NOR logic resulting in a low output for an off–state while the SG3527A utilized OR logic which gives a
high output when off.
• 8.0 V to 35 V Operation (maximum 40vdc)
• 5.1 V ± 1.0% Trimmed Reference
• 100 Hz to 400 kHz Oscillator Range (maximum 500KHZ)
• Separate Oscillator Sync Pin
• Adjustable Deadtime Control
• Input Undervoltage Lockout
• Latching PWM to Prevent Multiple Pulses
• Pulse–by–Pulse Shutdown
• Dual Source/Sink Outputs: ±400 mA Peak
Видео #276 SG3525A / SG1525A / SG2525A Pulse Width Modulation PWM / SMPS Controller канала Haseeb Electronics
i explained SG3525A / SG1525A / SG2525A Pulse Width Modulator Controller functional description, pinout, circuit diagram and test circuit
The SG3525A, SG3527A pulse width modulator control circuits offer
improved performance and lower external parts count when implemented for controlling all types of switching power supplies i,e. buck converter, forward converter, half bridge, full bridge, push pull, boost converter, buck boost converter, continuous or discontinuous mode flyback SMPS. its on–chip +5.1 V reference is trimmed to ±1% and the error amplifier has an input common–mode voltage range that includes the reference voltage, thus eliminating the need for external divider resistors. A sync input to the oscillator enables multiple units to be slaved or a single unit to be synchronized to an external system clock. A wide range of dead-time can be programmed by a single resistor connected between the CT and Discharge pins. These devices also feature built–in soft–start circuitry, requiring only an external timing capacitor. A shutdown pin controls both the soft–start circuitry and the output stages, providing instantaneous turn off through the PWM latch with pulsed shutdown, as well as soft–start recycle with longer shutdown commands. The under voltage lockout inhibits the outputs and the changing of the soft–start capacitor when VCC is below nominal. The output stages are totem–pole design capable of sinking and sourcing in excess of 200 mA. The output stage of the SG3525A features NOR logic resulting in a low output for an off–state while the SG3527A utilized OR logic which gives a
high output when off.
• 8.0 V to 35 V Operation (maximum 40vdc)
• 5.1 V ± 1.0% Trimmed Reference
• 100 Hz to 400 kHz Oscillator Range (maximum 500KHZ)
• Separate Oscillator Sync Pin
• Adjustable Deadtime Control
• Input Undervoltage Lockout
• Latching PWM to Prevent Multiple Pulses
• Pulse–by–Pulse Shutdown
• Dual Source/Sink Outputs: ±400 mA Peak
Видео #276 SG3525A / SG1525A / SG2525A Pulse Width Modulation PWM / SMPS Controller канала Haseeb Electronics
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
![](https://i.ytimg.com/vi/65BRSp_5QqU/default.jpg)
![#78 SG3525A / SG1525A / SG2525A Pulse Width Modulation PWM / SMPS Controller](https://i.ytimg.com/vi/Xtw-gTp36uQ/default.jpg)
![How a 3 Phase Pulse Width Modulation (PWM) VFD Inverter Works Simulation](https://i.ytimg.com/vi/wvzUE_Q9AhI/default.jpg)
![Lynx RS4-2000 PA Amplifier Repair - SMPS Switch Mode PSU Fault LER#146](https://i.ytimg.com/vi/cMdyrP5qWUw/default.jpg)
![SG3525, KA3525, UC3525 ¡Explicación COMPLETA! - Parte 1](https://i.ytimg.com/vi/_66zEjoxY7A/default.jpg)
![[386] How to Calculate Startup Resistor / Resistance to Design SMPS Switch Mode Power Supply](https://i.ytimg.com/vi/2Xec7ZMNEMI/default.jpg)
![How To Make Simple Inverter using IRFz44 Mosfet & sg3525 #DCtoAC #inverter #Mosfetinverter](https://i.ytimg.com/vi/JQgDR03LU_k/default.jpg)
![How to Troubleshoot Electronics Down to the Component Level Without Schematics](https://i.ytimg.com/vi/QFAWb1F_EpE/default.jpg)
![220V to 12V 20A](https://i.ytimg.com/vi/xyaa8eaQ7hE/default.jpg)
![SG3525 inverter 12V TO 220V | 50HZ & 60HZ | 300W](https://i.ytimg.com/vi/-z32yN-mtsQ/default.jpg)
![#236 Current Mode PWM SMPS controller UC3842 /UC3843 / UC3844 / UC3845 Functional Description](https://i.ytimg.com/vi/v-HnwsbBOVE/default.jpg)
![#277 Understanding OPTOCOUPLER or OPTO-ISOLATOR](https://i.ytimg.com/vi/G-RxXPesTqc/default.jpg)
![INVERSOR DC/AC de onda cuadrada con SG3525 y protección de batería baja con FUNCIONAMIENTO PERFECTO](https://i.ytimg.com/vi/ZCZqXBD3UyM/default.jpg)
![{559} How To Calculate Switching Frequency for UC3842 / 3843 /3844 /3845 Oscillator Frequency](https://i.ytimg.com/vi/q187Op2DwVA/default.jpg)
![Build A Simple Pulse Width Modulation Controller / PWM](https://i.ytimg.com/vi/mjIubJeTRyY/default.jpg)
![#EP-169 SG3525 Tutorial !!! Learn Everything About This. E-Rikshaw Charging IC.](https://i.ytimg.com/vi/QVQmaJwEnX0/default.jpg)
![12V 60A from 220VAC SMPS High Current for motor](https://i.ytimg.com/vi/Ne54L2YCC9Y/default.jpg)
![How to make inverter 12v to 220v 50hz | KA3525 SG3525](https://i.ytimg.com/vi/6hYKn2HlfRA/default.jpg)
![Power Supply Troubleshooting and Repair Tips](https://i.ytimg.com/vi/pffOJdCQ7kw/default.jpg)
![#315 Switch Mode Power Supply SMPS working principle (Soft start startup, running & feedback)](https://i.ytimg.com/vi/RcH57E1IG0U/default.jpg)