How to Build Eclipson Model V - RC 3D Printed Airplane

Full Step by step instructions to assemble a full 3d printed RC airplane designed by Eclipson. This is a redesign of the Eclipson Model V. This plane is fun to fly and very easy to assemble.

Thank you so much for watching!

If you like videos like this, consider buying me a coffee, it really supports me: https://www.buymeacoffee.com/troymcmillanrc

See what else I am working on: https://www.instagram.com/troymcmillan_rc/
#3Dprinted,#RCairplane, #ItFlies

STL Files: https://www.eclipson-airplanes.com

Artillery Sidewinder 3D Printer: https://amzn.to/396eqIp
Artillery Genius 3D Printer: https://amzn.to/39cA6CZ
LW-PLA: https://colorfabb.com/lw-pla-natural
varioShore TPU: https://colorfabb.com/varioshore-tpu-black
White PLA: https://amzn.to/3ghcHl1
Black PLA: https://amzn.to/30E4YIT
TPU: https://amzn.to/2Sw3Oe8
AR620 Receiver: https://amzn.to/3j4PbK4 DX6
DX6 Transmitter: https://amzn.to/3l6NFsD
2212-13 1400KV Motor: https://amzn.to/2P13PYU
8x6 Propeller: https://amzn.to/36cf3yL
1000mAh Battery: https://amzn.to/353cLmf
450mAh Battery: https://amzn.to/3k4lY1J
4x 9g servos: https://amzn.to/31kj82B
10x5x3 Magnets: https://amzn.to/3bzb4Pz
2x8mm Screws: https://amzn.to/3p8gmqY
1mm Carbon rods: https://amzn.to/32lEoW2
1/8” Wheel Collar: https://amzn.to/3p4tvl1
3pin wire assortment: https://amzn.to/3l1xNYt
XT60 connector: https://amzn.to/3iyZWnf
2mm push rod ends: https://amzn.to/3nnjD4U
Z-Bend pliers: https://amzn.to/34mA0rt
Print Settings for LW-PLA
Quality:
Layer Height – 0.25
Line Width – 0.4
Shell:
Wall Line Count – 1
Z Seam Alignment - User Specified
Z Seam Position - Front (Rotate model to have best Location for seam)
Seam Corner Preference - Expose Seam
Infill:
Infill Density – 0
Material:
Printing Temperature – 235
Build Plate Temperature – 60
Flow – 53%
Speed:
Print Speed – 100
Outer Wall Speed – 55
Inner Wall Speed – 55
Travel Speed – 100
Travel:
Combing Mode – off
Enable Retraction – Checked
Retraction Distance – 3 (Stringing cannot be eliminated with LW-PLA)
Retraction Speed – 10mm/s
Retraction Extra Prime Amount – 0.3
Cooling:
Enable Print Cooling – Checked
Fan Speed – 100
Minimum Layer time - 5
Mesh Fixes:
Union Overlapping Volumes – Checked
Special Modes:
Surface Mode – Normal
Experimental:
Slicing Tolerance – Middle
Disclaimer: I am sponsored by some of the products I mention. However, all of my opinions are my own. Some of the above links are affiliate links, that does not effect the price you pay for a product, but I may receive a small commission if you make a purchase. This helps support my channel and allows me to continue to make videos like this. Thank you for your support!!

Видео How to Build Eclipson Model V - RC 3D Printed Airplane канала Troy McMillan