How to Build RC 3D Printed ASK14 Glider - Planeprint

I will show step by step the full process to assemble this ASK14 Glider. I will show some flight video from the maiden flight. This glider has a 2.5 meter wing span and flies very well. Links bellow to all the parts and materials. The STL files can be purchased from Planeprint.com.
Thank you so much for watching!

If you like videos like this, consider buying me a coffee, it really supports me: https://www.buymeacoffee.com/troymcmillanrc

See what else I am working on: https://www.instagram.com/troymcmillan_rc/

STL Files: https://www.planeprint.com/ask14
How to Print Thin Wall: https://www.youtube.com/watch?v=TZ_-AespXDw&t=2s
Artillery Sidewinder Review: https://www.youtube.com/watch?v=DDZPZbcnwAs&t=215s

Products Mentioned:
Artillery Sidewinder 3D Printer: https://amzn.to/396eqIp
Artillery Genius 3D Printer: https://amzn.to/39cA6CZ
LW-PLA: https://colorfabb.com/lw-pla-natural
Red PLA: https://amzn.to/3tjfIt3
White PETG: https://amzn.to/2MvroIx
Clear PETG: https://amzn.to/3tmzvrr
Black TPU: https://amzn.to/2Sw3Oe8
CA Glue: https://amzn.to/2J8EvNW
CA Accelerator: https://amzn.to/3fpbycz
3536 1450kv Motor: https://amzn.to/3aAllu8
60amp ESC: https://amzn.to/3rjBMSj
9x4 Prop: https://www.masterairscrew.com
2x HS-55 Servos: https://amzn.to/3oRnDKV
4x HS-40 Servo: https://amzn.to/3m3hnPi
2700mah 3S Battery: https://amzn.to/34ttPjJ
AR620 Receiver: https://amzn.to/3j4PbK4
DX6 Transmitter: https://amzn.to/3l6NFsD
3pin wire assortment: https://amzn.to/3l1xNYt
XT60 connector: https://amzn.to/3iyZWnf
Y-Harness: https://amzn.to/3jAFwvo
5mm magnet: https://amzn.to/35ZPLoN
3mm Steel Rods: https://amzn.to/39KV8tS
Lead weight: https://amzn.to/3cFnzeu
Screw assortment: https://amzn.to/2SvMxSs
2mm push rod ends: https://amzn.to/3nnjD4U
Z-Bend pliers: https://amzn.to/34mA0rt
Hot knife: https://amzn.to/34AGOB1
Drill Bits: https://amzn.to/3nIJzrx
Carbon Rods: https://www.readymaderc.com
Onboard Camera: https://amzn.to/3rp2OrH

32mmx25mm Retracts:
https://hobbyking.com/en_us/electric-retract-with-reversible-mount-1pc-18-8g.html?wrh_pdp=2
https://hobbyking.com/en_us/servoless-retract-with-metal-trunion-for-small-models-32mm-x-25mm-mount-2pcs.html?wrh_pdp=2
https://www.horizonhobby.com/product/e-retract--zero-1100mm/FMMPJ119.html
https://www.horizonhobby.com/product/e-retract-p-51-strega-voodoo/ROHKA122.html
https://www.horizonhobby.com/product/retract--p39-hells-bells-980mm/FMMPI110.html
https://www.horizonhobby.com/product/e-retract-p-39/ROHKG111.html
*These are the settings I used for my Artillery Sidewinder 3D Printer. These settings are not going to work with every printer, or every PLA. Printers have different length bodin tubes, and PLA’s have different melting points. These may not work exactly for you, but should give you a good base to start with if you have a similar size printer. Good luck!

Profile 3 Cura Settings:
Quality:
Layer Height – 0.25
Line Width – 0.4
Shell:
Wall Line Count – 1
Infill:
Infill Density – 0
Material:
Printing Temperature – 230
Build Plate Temperature – 60
Flow – 100
Enable Retraction – Checked
Retraction Distance – 1.3
Retraction Speed – 10
Retraction Extra Prime Amount – 0.3
Speed:
Print Speed – 100
Outer Wall Speed – 35
Inner Wall Speed – 35
Travel Speed – 80
Travel:
Combing Mode – off
Cooling:
Enable Print Cooling – Checked
Fan Speed – 50
Mesh Fixes:
Union Overlapping Volumes – NOT Checked
Special Modes:
Surface Mode – Surface
Experimental:
Slicing Tolerance – Middle
Disclaimer: I am sponsored by some of the products I mention. However, all of my opinions are my own. Some of the above links are affiliate links, that does not effect the price you pay for a product, but I may receive a small commission if you make a purchase. This helps support my channel and allows me to continue to make videos like this. Thank you for your support!!

Видео How to Build RC 3D Printed ASK14 Glider - Planeprint канала Troy McMillan