Garage Workshop Super Insulated Radiant Floor
How I made my Garages Super Insulated Concrete Floor. This building is going to be heated because it is both a garage and a shop. I set up radiant tubes in the floor for the hot water to circulate. This is a hydronic radiant floor. I insulated between the ground and the concrete slab because the slab is always going to be hotter than the ground.
There is lots of rebar, probably over doing it a bit. The slab was 5,000 psi concrete and 5 inches thick. This slab is way overkill, but I didn't want to worry about it. Now I could add a lift in the future if I want to.
The foam board used is high-density "Geo Foam" which came out of a factory in RI. The foam was great and I would use it again. I secured it to the walls using Loctite power grab adhesive. There is a link below. The floor insulation is a total of 14 inches (R-56) and the wall is 2 inches (R-8). The wall was later framed out for another R-20 of cellulose.
Read more details about this project here: https://www.davidpoz.com/single-post/2017/09/19/Garage-Floor-Insulated-and-Heated
My dad and neighbor, John, are seen because they both helped out so much with this. Thank you.
Adhesive: http://amzn.to/2xyMzR1
We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites
Видео Garage Workshop Super Insulated Radiant Floor канала DavidPoz
There is lots of rebar, probably over doing it a bit. The slab was 5,000 psi concrete and 5 inches thick. This slab is way overkill, but I didn't want to worry about it. Now I could add a lift in the future if I want to.
The foam board used is high-density "Geo Foam" which came out of a factory in RI. The foam was great and I would use it again. I secured it to the walls using Loctite power grab adhesive. There is a link below. The floor insulation is a total of 14 inches (R-56) and the wall is 2 inches (R-8). The wall was later framed out for another R-20 of cellulose.
Read more details about this project here: https://www.davidpoz.com/single-post/2017/09/19/Garage-Floor-Insulated-and-Heated
My dad and neighbor, John, are seen because they both helped out so much with this. Thank you.
Adhesive: http://amzn.to/2xyMzR1
We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites
Видео Garage Workshop Super Insulated Radiant Floor канала DavidPoz
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
Hydronic Radiant Heating - Concrete ApplicationAdvanced Framing for Energy Efficient Garage WorkshopSolar Heated Garage Radiant Floor, UpdateThe RIGHT WAY to Insulate Your Concrete FloorConcrete Garage Foundations: How We Build Them at Site Preparations, LLCInstalling your own radiant heat tubing in a concrete slab. (DIY METHOD)Insulated Concrete Forms - Installation Training VideoInstalling a Heated Concrete Floor in Morton Barn40X 90 pole barn floor part 2Concrete Slab Preparation | Radiant In Floor Heat Ep12.3 Part 3/3Installing Foam Under Slab Insulation.MOVInstalling Under slab insulationMy New Shop: The Radiant SlabInstalling Radiant Pex Tubing In Concrete Slab Pole Barn House Ep 8How to implement radiant floor heating. Installing viega rapid grid a basement and garage.How to Build and setup a Concrete Foundation for Garages, Houses, Room additions, Etc Part 1How to Install In Floor Heat in a WorkshopYou've Probably Never Seen A Concrete Pour Like This Before, Insulated Kiln SlabDON'T INSULATE YOUR BASEMENT until you watch this...