How To Build Flame Thrower Exhaust!!! (Stand Alone Ignition System)
On this episode of Make It Kustom, I show you step by step how to build a stand alone ignition system for a flame thrower exhaust for your “BBQ” 😉
Materials needed:
1- toggle switch
3- 5 pin 30 amp relays (with holders)
1- 30 amp in-line fuse holder
2- ignition condensers (points ignition)
1- ballast resistor (1975/76 Chrysler)
2- ignition coils
2- spark plugs
2- spark plug wires
2- 14mm x 1.25 nuts (to weld in your pipes)
Shop merch and hammers here ⬇️⬇️⬇️
https://www.japhandskustoms.com/shop
#makeitkustom #japhandskustoms #kustom
Видео How To Build Flame Thrower Exhaust!!! (Stand Alone Ignition System) канала Make It Kustom
Materials needed:
1- toggle switch
3- 5 pin 30 amp relays (with holders)
1- 30 amp in-line fuse holder
2- ignition condensers (points ignition)
1- ballast resistor (1975/76 Chrysler)
2- ignition coils
2- spark plugs
2- spark plug wires
2- 14mm x 1.25 nuts (to weld in your pipes)
Shop merch and hammers here ⬇️⬇️⬇️
https://www.japhandskustoms.com/shop
#makeitkustom #japhandskustoms #kustom
Видео How To Build Flame Thrower Exhaust!!! (Stand Alone Ignition System) канала Make It Kustom
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
Making a Hand Carved Skull Shift Knob From Brass For the 100k Subs Giveaway
How-To TIG BUTT Weld Sheet Metal Restoration Panels 1932 Ford Split Grill On Model A Roadster
EP-14 INSTALLING AIR BAGS AND CUSTOM 3 - LINK SUSPENSION MIG WELDING & FABRICATION HALFASS KUSTOMS
WHAT DO YOU THINK? Mounting Headlights, Tail lights, Shocks, & MORE! Model A Roadster
How To Fabricate a Custom Firewall Using a Motorized Bead Roller (Model A Roadster Build Part 4)
How-To Reverse Curve w/ Power Hammer Metal Shaping Linear Stretch At Bespoke Coachworks
Amazing "STACK A TACK" MIG Welding TECHNIQUE = NO WARPING! Finishing the Dash 1930 MODEL A
Installing Steering COLUMN, BOX, WHEEL & SHAFTS, 1931 Model A Hot Rod
Trouble with DUAL SHOCKS? Finishing Rear Suspension COE RAMP TRUCK EP-18
MIG WELDING for a PERFECT RESULT "A" Pillars 1939 Lincoln Zephyr Coupe Conversion
Your Questions ANSWERED!! What’s Been Going On At The Shop Lately???
EASY 2 MAKE! DIY STRETCHER TOOL! HOW-TO Make "REVERSE"CURVED FLANGES on SHEET METAL
Survivor Boogie Van “EXCALIBUR” Sold + Delivered!! Rocky Mountain Road Trip
COE Ramp Truck EP-8 Fabricating Under Floor Hydro Boost Brake System That Tilts w The Cab
HOW TO Hammer Weld Sheet Metal TIG MIG "I'd Still Buy One!" WHY? SSimder Upgraded SD-4050 Pro Welder
Shop Move UPDATE!! Upcoming Build Plans + What’s Next for Japhands Kustoms?!!
COE Ramp Truck EP - 10 Cab Mount FABRICATION / INSTALL YORK ENGINE DRIVEN Compressor AIR BAGS
Check Out Some COOL CARS!! Local Summer Car Meet Up | CAFFEINE N’ GAS-O-LEAN
EASY BODY LINE RUST REPAIR - MIG Welding And PROFILING Tool NOT BEADROLLER Dan's 34' Ford PU
GIANT FABRICATED Rear Sway Bar For The COE RAMP TRUCK EP-17
IS THIS RIGHT? Designing/Fabricating DUAL SHOCKS COE RAMP TRUCK EP-15