How to Modify a Dunlop Jimi Hendrix Signature Fuzz Face (Fuzz Face History)

Today I'm showing you how to modify the Dunlop Jimi Hendrix Signature Fuzz Face. You will have solder in your face. You will have fuzz in your ears. It will be glorious. This mod makes a Fuzz Face really fun and gives you a good bit more range of sound than the stock Fuzz Face. Let me know what you think in the comments! Also check out Deep Sea Diver's History Speaks and let me know what you think!

https://thejhsshow.com/
https://www.patreon.com/thejhsshow
https://www.jhspedals.info/

Record Time:
Deep Sea Diver - History Speaks https://amzn.to/2xLHJBE

MODDED FUZZ FACE GIVEAWAY https://thejhsshow.com/giveaway

MOD INSTRUCTIONS:

FUZZ FACE: https://www.jimdunlop.com/jimi-hendrix-fuzz-face-distortion/

TOOLS
Soldering iron https://amzn.to/3bOWkKY
Solder https://amzn.to/2V1nIyf
Needle nose pliers https://amzn.to/2UXXahv
Wire strippers https://amzn.to/3dR5GYa
Wire cutters https://amzn.to/2wZ8phK
Screw drivers https://amzn.to/2yxywgf
Sockets or wrenches: https://stompboxparts.com/tools/rocket-socket-nut-drivers/
Solder braid or solder sucker https://amzn.to/2wRQNEC

PARTS
500K B POT:
10mm Pot https://www.mouser.com/ProductDetail/Alpha-Taiwan/RV16AF-10-15R1-B500K-3LA?qs=sGAEpiMZZMukHu%252BjC5l7YV63gJvf%252BKJmFWiTjWytTUs%3D
Better 24mm Pot https://amzn.to/3asJCjO

10K B POT:
10mm Pot https://www.mouser.com/ProductDetail/Alpha-Taiwan/RV16AF-10-15R1-B10K-3LA?qs=sGAEpiMZZMukHu%252BjC5l7YWY0Wy3FSR3VdvZ35yOs388%3D
Better 24mm Pot https://amzn.to/2KtJAO7

1 MEG C POT:
10mm Pot https://www.mouser.com/ProductDetail/Alpha-Taiwan/RV16AF-20-15K-C1M-3LA?qs=sGAEpiMZZMtC25l1F4XBU1WvpdUcjC%2F6nxPclOOgDXkQI5nuUkBbfA%3D%3D
Better 24mm pot https://amzn.to/2KvP8aY

Wire https://amzn.to/2xNzt3q

OPTIONAL
Multi Meter https://amzn.to/2X41y10
Cup/Parts Tray for holding parts you remove https://amzn.to/2xL5OrT
Heat shrink https://amzn.to/2UCk4Mm
Drill (if you want to get crazy) https://amzn.to/39HopSR
Hot Glue Gun-Glue or 3m Tape https://amzn.to/3dTtE56
Circuit Board Holder "Third Hand": https://amzn.to/34YViK5
BE SURE YOU SOLDER PROPERLY. WATCH THE VIDEO BELOW!
TAKE YOUR TIME. IF YOU RUSH, YOU WILL REGRET IT.

HOW TO SOLDER: https://www.youtube.com/watch?v=oqV2xU1fee8

OPTIONAL MOD IDEAS
Battery clip to 9v adapter http://www.voodoolab.com/shop/index.php?cPath=22_24_40

STEP 1: Remove Hardware and Prep Things
Remove back plate - Philips head screw
Remove knobs. Flat head screw driver
Remove pot hardware
Label Pots for memory :-)
Unscrew PCB - Phillips head

STEP 2: Change volume pot from 470k-A to 500K-B
(More powerful volume taper / slight eq effect)
Mount 500K-B into case. Use plastic washer from OG pot (#10 Socket)
Unsolder one wire at a time from OG pot and solder on to new mounted pot

STEP 3: Fix OG Fuzz pot internally
(IMHO the fuzz pot is useless. Max it out and mount it inside. Clean up with guitar!)
Place hardware back on just in case you ever want to reverse this mod
Mount with two layers of 3m tape or hot glue

STEP 4: Move VR2 to external Fuzz position
(Gives an external adjustment of the bias control! So much better than the OG control)
Heat single leg of trim pot and gently lift
Take two wires and strip ends
Tin the wire
Place heat shrink on them (optional)
Solder top left pad to lug 3 of the 10K-B pot
Solder bottom single pad to lug 2 of the 10KB-pot
Mount the new pot into the old FUZZ spot, use the plastic washer from the OG pot
This pot adjust the voltage to the collector of Q2
The standard setting for this control is 4.5v (DMM)
Lets you go from gated fuzz / normal fuzz / stronger fuller tones

STEP 5: Replace R2 20K and VR1 trim pot w/ internal pot
(Even more adjustment of how the stages interact. Using a full size pot for ease and also lets you drill and mount externally if you are a little crazy….)
Remove VR1 gently from PCB
Jumper across the old VR1 pads
Unsolder R2 from PCB and remove
Take two wires and strip ends
Tin the wire
Place heat shrink on them (optional)
Solder one wire into old R2 PCB hole and then to lug 3 of the 1 MEG C pot
Solder another wire into the other old R2 PCB hole and then to lug 2
Pot down is 1v ish (stock setting)
Pot up is 8v ish (kills sound completely)
Barely backing it up will jump down to around 3.5v and give you some unique tones

STEP 6: Place the backplate on
STEP 7: Pick knobs: https://amzn.to/2KzhXD7
STEP 8: Sign it, date it and be proud!

OPTIONAL MOD IDEAS
- Battery clip to 9v adapter
- Change out transistors with other NPN Is types
- Step 2,3,4 will work on virtually ANY Fuzz Face!

TONE TIPS:
- Guitar directly in…. NO exceptions
- Fuzz is an instrument. Play to it not with it.
- Experiment with your guitars volume
- Place a Tubescreamer after!

#jhs #thejhsshow #fuzzface

Видео How to Modify a Dunlop Jimi Hendrix Signature Fuzz Face (Fuzz Face History) канала JHS Pedals