Guide of replacing the motherboard of ender3 with BTT SKR MINI E3 V2.0 and BTT TFT35 E3 V3.0
BTT SKR MINI E3 V2.0 and BTT TFT35 E3 V3.0 was designed by BIGTREETECH. We are committed to easy printing, easy life.
BTT SKR MINI E3 V2.0
1.The TMC2209 driver use same physical UART port, which save IO and increase the stability of motor drivers.
2.We increase an double Z-axis interface on the motherboard which can work on printer with single or double Z-axis.
3.We set a EEPROM( AT24C32) on the board , so data storage is more stable.
4.Printed circuit boards of SKR MINI E3 V2.0 have 4 layers, which prolong the life of this board.
5.Power chip is MP1584EN and increase the current output which can reach to 2.5A.
6.We add protective device to interface of thermistor.
7.We also set two numerical control fan and a interface (PS-ON) for automatic shutdown after printing.
8.SKR MINI E3 V2.0 also supports BL touch, filament run-out sensor, power-off resumed printing, and automatic shutdown after printing.
BTT TFT35 E3 V3.0
1.ARM Cortex-M3 series STM32F207VCT6 chip with 32-bit CPU 120MHz;
2.Upgrade the firmware by SD card. It is easy and convenient to operate.
3.This display board has higher compatibility. Users can select two work modes: UART serial port screen mode and 12864 screen mode.
4.Serial port screen mode supports two printing modes: SD card and U disk.
5.Reserve WIFI port, and WIFI function is realized by external WIFI module;
6.Reserve the extension port of filament breaking detection (FIL-DET);
7.Reserve the extension port of automatic shutdown after printing (PS-ON);;
8.LCD12864 mode uses EXP1, EXP2 and EXP3. EXP1 and EXP2 are LCD screen ports of normal motherboard. EXP3 is the LCD interface used by E3 series motherboard (such as SKR MINI E3 V1.2, SKR E3 DIP V1.1, etc.) ;
BIGTREETECH:http://www.bigtree-tech.com/wiki/show...
Facebook: https://www.facebook.com/BIQU3DPRINTER/?ref=bookmarks
Twitter: https://twitter.com/BIQU_Hope
Instagram: https://www.instagram.com/btt_daisy/
Видео Guide of replacing the motherboard of ender3 with BTT SKR MINI E3 V2.0 and BTT TFT35 E3 V3.0 канала BIGTREETECH
BTT SKR MINI E3 V2.0
1.The TMC2209 driver use same physical UART port, which save IO and increase the stability of motor drivers.
2.We increase an double Z-axis interface on the motherboard which can work on printer with single or double Z-axis.
3.We set a EEPROM( AT24C32) on the board , so data storage is more stable.
4.Printed circuit boards of SKR MINI E3 V2.0 have 4 layers, which prolong the life of this board.
5.Power chip is MP1584EN and increase the current output which can reach to 2.5A.
6.We add protective device to interface of thermistor.
7.We also set two numerical control fan and a interface (PS-ON) for automatic shutdown after printing.
8.SKR MINI E3 V2.0 also supports BL touch, filament run-out sensor, power-off resumed printing, and automatic shutdown after printing.
BTT TFT35 E3 V3.0
1.ARM Cortex-M3 series STM32F207VCT6 chip with 32-bit CPU 120MHz;
2.Upgrade the firmware by SD card. It is easy and convenient to operate.
3.This display board has higher compatibility. Users can select two work modes: UART serial port screen mode and 12864 screen mode.
4.Serial port screen mode supports two printing modes: SD card and U disk.
5.Reserve WIFI port, and WIFI function is realized by external WIFI module;
6.Reserve the extension port of filament breaking detection (FIL-DET);
7.Reserve the extension port of automatic shutdown after printing (PS-ON);;
8.LCD12864 mode uses EXP1, EXP2 and EXP3. EXP1 and EXP2 are LCD screen ports of normal motherboard. EXP3 is the LCD interface used by E3 series motherboard (such as SKR MINI E3 V1.2, SKR E3 DIP V1.1, etc.) ;
BIGTREETECH:http://www.bigtree-tech.com/wiki/show...
Facebook: https://www.facebook.com/BIQU3DPRINTER/?ref=bookmarks
Twitter: https://twitter.com/BIQU_Hope
Instagram: https://www.instagram.com/btt_daisy/
Видео Guide of replacing the motherboard of ender3 with BTT SKR MINI E3 V2.0 and BTT TFT35 E3 V3.0 канала BIGTREETECH
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
Big Tree Tech SKR Mini E3 V2.0 - Silent Main Board - Install - Chris's BasementBTT TFT35 dual mode touch screen guideFirst 24 Upgrades & Mods for my Ender 3 ProLinear rails guide and test on Ender 3 and Ender 5MKS Robin E3 vs BTT SKR E3 Turbo - Complete mainboard upgrade guideSetting Z-Offset for a BLTouch (or another probe)SKR Mini E3 V2.0 - Complete guide to the best value Ender 3 upgradeSKR Mini E3 V2.0 + TFT35 Installation Guide + BLT Upgrade (ENDER 3/ENDER 3 Pro)SKR Mini E3 - The best Ender 3 upgrade from stock?SKR 1.3 / 1.4 - TFT35 Display Installation and Marlin 2 0 configurationBest Upgrade For Your Creality Ender 3 3D Printer In 2020 | SKR Mini E3 V1.2Creality Ender 3 Pro BigTreeTech TFT35 E3 V3.0 Touch Screen Upgrade Review | GOOD but some gotchas!Add wifi to your Bigtreetech mainboard/touchscreen - ESP-01S guideBigtreetech Ender 5 Plus Upgrade: SKR Mini E3 V2.0 (Part 3)BTT Smart filament sensor guide - Detect filament runout and jamsBig Tree Tech 7" Touchscreen TFT70 V3.0 - Super Cool - Chris's BasementCreality 32 bit V4 board guide - Ender 3 V2, BLtouch & moreBTT TFT35 firmware upgrade - What you should knowBigtreetech SKR V1.4 (Turbo) comprehensive guideMesh Bed Level on Creality Ender 3 with SKR Mini E3