How To Install A Surge Protector

In the last video we took a deep dive into Surge Protection, today let's install 'em! Watch as Dustin installs two different styles of Type 1, Whole-Home surge protectors... Plus the how, why, and where of it all.
SPONSOR: Schneider Electric
https://homedepot.sjv.io/c/1240960/963729/8154

👾🤖PRACTICE EXAMS🤖👾
https://www.electricianu.com/practice-exams

😎👕MERCH👕😎
https://www.electricianu.com/merchandise

📲👥SOCIALS👥📲
Instagram - https://www.instagram.com/electrician_u
Discord - https://discord.gg/7ykYfbh
Facebook Page - https://www.facebook.com/theelectricianu
Facebook Group - https://bit.ly/2tz7eQh
TikTok - https://www.tiktok.com/@electricianu
Reddit- https://www.reddit.com/r/ElectricianU/

SPDs? You should get that checked out.

These days our homes seem to be spilling over with new technology and sensitive electronics, thus the surges of yesterday are only getting more and more costly. Most homeowners blame lightning for the majority of electrical surge damage to their home... but they're being a bit misled. These voltage abnormalities more commonly come from large appliances in our homes (ACs, furnaces, air compressors etc.), rarely by lightning or changes to the power grid. Surges shorten the life of sensitive electronics, the larger ones causing catastrophic damage to a homes electrical system. Surge Protection Devices or (SPDs) are devices installed at electrical services, branch circuits, or equipment that help protect against these sudden spikes in voltage, using special resistors to “sense” when higher-than-normal voltage is produced then immediately act to redirect voltage away from your electrical system. It's important to note that surge protectors do not protect against lightning strikes to the home or building itself, that would be a lightning protection system which is something completely different, so get that out of your head right meow. To learn more about surges and how surge protection works, go check out Dustin’s deep dive into surge protection -- https://youtu.be/aoNu1TX8IH0

Installation
In Dustin's video you will see two different styles of Type 1 “whole home” Surge protection, the first being the snap-in, plug-on neutral style with no leads. This is a newer Square D design that only works with the corresponding QO plug-on-neutral panels. Not only is this style super-sleek and convenient for the installer, but if installed correctly is as close to line as physically possible, meaning its rated efficacy is near 100%. Simply save two breaker spaces of the breaker bus and snap in the surge protector, the green LED light should come on indicating that it's functioning and ready for surges.... and you're done! Simple as apple pie and ice cream.
The second style is intended for more universal use, designed to be mounted to the exterior of any make and model of panel with a threaded hub and lock ring attachment that fits into a ½ inch knock-out at either the bottom or the side of a panel. While this Type 1 is rated for use without an overcurrent protection device, for proper installation it is easiest to land the leads into a breaker that is installed at the nearest space possible to keep the leads short. If the panel being worked on has the option, this specific SPD is also rated to be directly wired to the phase bus mounting screws. When installing this style of SPD it is crucial to keep the leads as short as possible because with every foot of wire lead, 160 more volts is allowed to pass through to the load you’re trying to protect in the event of a surge.
For the full article visit:
http://electricianu.com/video/how-to-install-a-surge-protector/

Stay safe out there! Love from the ATX
#surgeprotector #surgeprotection #lightingprotection
--
Subscribe - https://www.youtube.com/c/electricianu?sub_confirmation=1

IF YOU ENJOY THESE VIDEOS PLEASE SUBSCRIBE AND "LIKE" THEM ABOVE. ALSO CHECK OUT THE ELECTRICIAN U PODCAST ON ITUNES AND SPOTIFY!!

Видео How To Install A Surge Protector канала Electrician U