17 Super Tips for Chainsaw Milling (Make Better Boards!)

These 17 chainsaw milling tips show you how to put your alaskan mill in action making logs into boards. They will improve the quality of timber you can make with your mill, and/or influence the design of your mill if your thinking about making one. They are mainly a reply to your questions about various aspects of milling as well as being common mistakes I see being made and have made myself!

Subscribe to my channel for interesting diy projects! https://www.youtube.com/floweringelbow?sub_confermation=1

More chainsaw milling videos: https://goo.gl/8mTCyg

Lets Connect!
Patreon: https://www.patreon.com/floweringelbow
My website: http://www.FloweringElbow.org
FB: https://www.facebook.com/floweringelbow/

The tips:
ONE 00:18 Quality of cut can be improved greatly by easing the saw into the cut. Don’t go full throttle straight away, instead both start and stop slowly. Same if you have to stop mid slab for any reason.

TWO 00:53 Don’t push the saw! Ideally position the log on a slight gradient so the saw is a little bit 'gravity fed'. Winches get good reviews - I have never seen much need as a good sharp chain will pull itself into the cut.

THREE 01:22 Wedges. Talk about shape etc. Don’t hammer them into the kerf - it will change the angle of the straight edge and cause deep gouges.

FOUR 02:02 Angle the saw, nose first, and hold the angle consistently. Seesawing will leave a poor finish.

FIVE 02:27 Using the straight edge for cuts after the first again can aid accuracy and safety.

SIX 03:11 Wear Proper protective equipment, including a good dust mask. I'm now using an integrated face shield and dust mask which I got from ebay, and its a complete game changer! I originally got it for all kinds of other workshop tasks like painting, epoxy use, and sanding. In the past, even when I wore a separate dust mask, I would get dry eyes - no more! For chainsaw milling it's perfect, giving good visibility and clean air, free of the cocktail of fumes you get from using a two stroke engine. It's the 3M 6800 full face equivalent which means it's a cheaper import (only about $30 here: https://goo.gl/kVGmyk), but I use it with the genuine 3m 6001 vapour filters. (ebay link: https://goo.gl/PNXNEq) .  My radio ear defenders I won in an Instructables contest.

SEVEN 03:47 Make a full checklist before you leave. You can see my full checklist here: http://www.floweringelbow.org/2018/invent/17-super-tips-for-chainsaw-milling/

EIGHT 03:57 Use a brush to remove dust round the caps before re-fuelling. CS milling is much more dusty than regular chainsaw use...

NINE 07:00 Enjoy yourself.

TEN 04:05 Check to see if you need to refuel between slab cuts. Don’t start a slab unless you have enough to finish it. Avoid running the tank dry while milling!

ELEVEN 04:42 Aux oilier talk.

TWELVE 05:20 Dampened handles!

THIRTEEN 05:39 Let the saw cool off with the engine idling after long cuts .

FOURTEEN 05:55 Slab moving is dangerous- assess the risks and make wise choices.

FIFTEEN 06:12 Play it cool when things don’t go your way. Something will not go according to plan (!) try and make the best of it.

SIXTEEN 06:34 Stash your gear up-wind of the saw site. Dust WILL cover everything.

SEVENTEEN 06:45 How much did the mill cost? The full build log here https://www.instructables.com/id/Chainsaw-Mill-Build-Use-Tips-n-Tricks/

DISCLAIMER: This video description contains affiliate links, which means that if you click on one of the e-bay links, and then buy it I’ll receive a small commission. This helps support the channel and allows me to continue to make videos like this. Thank you for the support!

Видео 17 Super Tips for Chainsaw Milling (Make Better Boards!) канала FloweringElbow