$130 for the gimbals alone?! Yup. RadioMaster AG01 all metal CNC gimbals for TX16S
Uncertain about what to buy? Check out THE ULTIMATE FPV SHOPPING LIST: https://www.fpvknowitall.com/ultimate-fpv-shopping-list
SUPPORT ME ON PATREON at: http://bit.ly/2Ep5Sia
THIS IS MY FULL TIME JOB. Here are other ways that you can support me: https://www.fpvknowitall.com/support-me/
---
I receive a commission (at no extra cost to you) if you make a purchase after clicking one of the affiliate links below.
Buy the V3 Full CNC Hall Gimbal for tX16S at:
* RadioMaster Store - https://bit.ly/3pqksNr
* GetFPV - https://bit.ly/3aUtf24
* NewBeeDrone - https://bit.ly/3pulsAA
* Banggood - https://bit.ly/3vBnqAh
--- TABLE OF CONTENTS ---
0:00 - Intro and commercial disclaimer
2:16 - All metal construction with ball bearings
4:04 - Gimbals are adjustable from the front plate without opening the radio
6:32 - How to remove the old gimbals
8:26 - Just how bad is the original gimbal compared to the AG01?
9:47 - Important: before you start installing!
10:49 - Finish installing the AG01 gimbal
M2.5 screw assortment: https://amzn.to/3EeEkb9
16:13 - Run radio gimbal calibration routine
17:23 - Compare jitter on the AG01 vs. the old gimbals
Why you should turn off OpenTX ADC filter: https://www.youtube.com/watch?v=hQZImPgbaj8
The 5000 mAh battery that I use in my radio is: https://bit.ly/3vdDDdj
18:22 - Conclusion: should you buy it?
Видео $130 for the gimbals alone?! Yup. RadioMaster AG01 all metal CNC gimbals for TX16S канала Joshua Bardwell
SUPPORT ME ON PATREON at: http://bit.ly/2Ep5Sia
THIS IS MY FULL TIME JOB. Here are other ways that you can support me: https://www.fpvknowitall.com/support-me/
---
I receive a commission (at no extra cost to you) if you make a purchase after clicking one of the affiliate links below.
Buy the V3 Full CNC Hall Gimbal for tX16S at:
* RadioMaster Store - https://bit.ly/3pqksNr
* GetFPV - https://bit.ly/3aUtf24
* NewBeeDrone - https://bit.ly/3pulsAA
* Banggood - https://bit.ly/3vBnqAh
--- TABLE OF CONTENTS ---
0:00 - Intro and commercial disclaimer
2:16 - All metal construction with ball bearings
4:04 - Gimbals are adjustable from the front plate without opening the radio
6:32 - How to remove the old gimbals
8:26 - Just how bad is the original gimbal compared to the AG01?
9:47 - Important: before you start installing!
10:49 - Finish installing the AG01 gimbal
M2.5 screw assortment: https://amzn.to/3EeEkb9
16:13 - Run radio gimbal calibration routine
17:23 - Compare jitter on the AG01 vs. the old gimbals
Why you should turn off OpenTX ADC filter: https://www.youtube.com/watch?v=hQZImPgbaj8
The 5000 mAh battery that I use in my radio is: https://bit.ly/3vdDDdj
18:22 - Conclusion: should you buy it?
Видео $130 for the gimbals alone?! Yup. RadioMaster AG01 all metal CNC gimbals for TX16S канала Joshua Bardwell
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
![New JB Edition TX16S Mk2 w/ built in ExpressLRS](https://i.ytimg.com/vi/6bFq3t6g0YI/default.jpg)
![AG01 gimbals now available for Zorro and TX12 Radiomaster radios!](https://i.ytimg.com/vi/Ro7mTVAPXCg/default.jpg)
![](https://i.ytimg.com/vi/o3UR62ziowg/default.jpg)
![The most advanced 65mm Whoop I've ever seen | HAPPYMODEL MOBEETLE6 FULL REVIEW](https://i.ytimg.com/vi/1ipOgKfwOrk/default.jpg)
![Everybody should be using these FPV Lua Scripts](https://i.ytimg.com/vi/RCS72GVR0gs/default.jpg)
![RC Controller Buyer's Guide January 2021 | JUMPER VS RADIOMASTER VS TANGO 2](https://i.ytimg.com/vi/DfX98yApzp4/default.jpg)
![RadioMaster AG01 CNC Hall effect gimbal. Some serious gimbal action...](https://i.ytimg.com/vi/BG6n7mnLtSU/default.jpg)
![Radiomaster AG01 CNC gimbal adjustments : stick tension, mode change, throttle ratchet & friction](https://i.ytimg.com/vi/K8aRgndgyp0/default.jpg)
![You're calibrating your gimbals wrong (solves Tango 2 THROTTLE warning)](https://i.ytimg.com/vi/I6n_Ak860lA/default.jpg)
![Radiomaster TX16S Mark II (2) - What's New?](https://i.ytimg.com/vi/XGbVPViNAyo/default.jpg)
![Which ExpressLRS module should you get?](https://i.ytimg.com/vi/JGS7Azztthw/default.jpg)
![Why build an FPV drone when GEPRC Mark 5 is this good?](https://i.ytimg.com/vi/JKIGDlbjyLs/default.jpg)
![This is the hottest upgrade for your Radiomaster TX16S - LED gimbal mod!](https://i.ytimg.com/vi/--_T0E6o-xs/default.jpg)
![How to install TX16S Gimbal Ring LEDs (official Radiomaster led kit)](https://i.ytimg.com/vi/sTZMmtzPxCc/default.jpg)
![Fitting Radiomaster AG01 Gimbals / Calibrating gimbals and drift testing / LED Gimbal backlights](https://i.ytimg.com/vi/ttLI9iVLD1I/default.jpg)
![Screen brightness on a knob? // EDGETX GLOBAL FUNCTIONS HOW-TO](https://i.ytimg.com/vi/CSWXkPCldP8/default.jpg)
![Radiomaster AG01 gimbal installation tips (Radiomaster TX16S MAX CNC gimbal upgrade)](https://i.ytimg.com/vi/7iqthHtzwIo/default.jpg)
![RadioMaster AG01 CNC Hall Sensor Gimbals Installation Guide](https://i.ytimg.com/vi/9ylNqidY7iw/default.jpg)
![Are those the best gimbals? Radiomaster AG01 gimbals](https://i.ytimg.com/vi/pViHVVjjuME/default.jpg)
![RadioMaster TX16S NEXT LEVEL Gimbals (AG01 CNC ALUMINUM HALL SENSOR & ADJUSTABLE!)](https://i.ytimg.com/vi/n8tuegngERc/default.jpg)