1999 BMW 328i (E46) - Plastic Coolant Hose Replacements Part 2
In this video, we carry on with the process of removing the intake manifold from the engine. We finally get the fuel rail popped out of the manifold, and the fuel lines disconnected from the rear of the engine bay (not the same spot indicated in the service manual), finally find and remove the lower intake manifold bracket, and the nine upper bolts. Then we remove the positive cable from the starter, and then remove a bunch of stuff that wasn't mentioned in the manual, including a vacuum line near the throttle body and some additional sensors and other wires.
Now we're set to replace the hoses, and that will be shown in Part 3 (and then afterwards the fun of putting everything back together!). The main issue we seemed to continuously run into are wires and lines that aren't mentioned in the Service Manual, or just typical old car problems with certain things not wanting to come off. It was also our first time taking a complicated manifold like this off and I suspect now that we've done it once, the next time we have to pull it off will go much quicker.
Chapters:
_____________________________________
0:00 - Introduction/ Continuing To Remove Fuel Rail From Manifold
1:20 - Removing Intake Bolts
3:00 - Blowing Air Into Crevice Between Intake Manifold & Engine
3:55 - Intake Manifold Removal Attempt #1
5:30 - Looking For & Removing Intake Manifold Lower Bracket
7:20 - Intake Manifold Removal Attempt #2
7:50 - Removing Vacuum Line Near The Throttle Body
8:05 - Finding & Removing More Stuff Holding Manifold On (Stuff Not Mentioned In Service Manual)
10:50 - Disconnecting Fuel Lines
12:40 - Removing Positive Cable From Starter
13:25 - Removing Intake Manifold
19:55 - Discussion & Preparation For Hose Replacements
21:40 - End Screen
Website Article: https://www.gbproductions.ca/1999-bmw-328i-e46-plastic-coolant-hose-replacements-part-2/
Don't forget to like, comment & subscribe if you're new
Visit our website @ https://www.gbproductions.ca/ for more content!
Twitter: https://twitter.com/GBProductions6
Instagram: https://www.instagram.com/gbproductions1/
Credits:
Presented By: Mitchell Greeley & Greg Bailey
Written By: Mitchell Greeley & Greg Bailey
Directed By: Mitchell Greeley & Greg Bailey
Director Of Photography: Mitchell Greeley & Greg Bailey
Produced By: Mitchell Greeley & Greg Bailey
Edited By: Mitchell Greeley
Camera: GoPro Hero 8 Black
Music From YouTube Audio Library
Production Code: 2021-056
Filmed On: May 3rd, 2021
Видео 1999 BMW 328i (E46) - Plastic Coolant Hose Replacements Part 2 канала GB Productions
Now we're set to replace the hoses, and that will be shown in Part 3 (and then afterwards the fun of putting everything back together!). The main issue we seemed to continuously run into are wires and lines that aren't mentioned in the Service Manual, or just typical old car problems with certain things not wanting to come off. It was also our first time taking a complicated manifold like this off and I suspect now that we've done it once, the next time we have to pull it off will go much quicker.
Chapters:
_____________________________________
0:00 - Introduction/ Continuing To Remove Fuel Rail From Manifold
1:20 - Removing Intake Bolts
3:00 - Blowing Air Into Crevice Between Intake Manifold & Engine
3:55 - Intake Manifold Removal Attempt #1
5:30 - Looking For & Removing Intake Manifold Lower Bracket
7:20 - Intake Manifold Removal Attempt #2
7:50 - Removing Vacuum Line Near The Throttle Body
8:05 - Finding & Removing More Stuff Holding Manifold On (Stuff Not Mentioned In Service Manual)
10:50 - Disconnecting Fuel Lines
12:40 - Removing Positive Cable From Starter
13:25 - Removing Intake Manifold
19:55 - Discussion & Preparation For Hose Replacements
21:40 - End Screen
Website Article: https://www.gbproductions.ca/1999-bmw-328i-e46-plastic-coolant-hose-replacements-part-2/
Don't forget to like, comment & subscribe if you're new
Visit our website @ https://www.gbproductions.ca/ for more content!
Twitter: https://twitter.com/GBProductions6
Instagram: https://www.instagram.com/gbproductions1/
Credits:
Presented By: Mitchell Greeley & Greg Bailey
Written By: Mitchell Greeley & Greg Bailey
Directed By: Mitchell Greeley & Greg Bailey
Director Of Photography: Mitchell Greeley & Greg Bailey
Produced By: Mitchell Greeley & Greg Bailey
Edited By: Mitchell Greeley
Camera: GoPro Hero 8 Black
Music From YouTube Audio Library
Production Code: 2021-056
Filmed On: May 3rd, 2021
Видео 1999 BMW 328i (E46) - Plastic Coolant Hose Replacements Part 2 канала GB Productions
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
Gaspe Peninsula Drive Dashcam Part 2 - Gaspe To Mont-Joli via Perce, Quebec (Quebec Route 132)Mk. 4 Volkswagen Jetta TDI Radiator Replacement Part 4Mk. 4 Volkswagen Jetta TDI - Turbo & Timing Belt Replacement Part 4Restoring a 1991 BMW 318i (E30) - Episode 31999 BMW 328i (E46) - Rear Brake Servicing Part 1Let's Get Started On Another Project // 1958 Case 600B Case-O-Matic Tractor Engine Rebuild Episode 11996 Volkswagen Golf GL RevivalParts Cleaning & Start Of Piston Reassembly // 1958 Case 600B Tractor Engine Rebuild Episode 9Removing The Oil Pan & Pistons // 1958 Case 600B Case-O-Matic Tractor Engine Rebuild Episode 51981 Volkswagen Rabbit Pickup Restoration Episode 4 // Donor Rabbit Engine Pull Part 2Restoring a 1991 BMW 318i (E30) - Episode 5How To Put A Tire On A Rim // A DIY Tutorial1999 BMW 328i (E46) - Coolant Hose Replacements Part 4Disassembling The Pistons // 1958 Case 600B Case-O-Matic Tractor Engine Rebuild Episode 61990 Volkswagen Jetta TD Cold Start VideoFuel Economy Challenge #1 - Mitchell's Road Trip To Sault Ste. Marie, OntarioMk. 4 Volkswagen Jetta TDI - Timing Belt Replacement Part 122002 Volkswagen Jetta TDI Cold Start Video #ShortsTotal Solar Eclipse Sky Time Lapse - April 8th, 2024 - Ridgeway, Fort Erie, OntarioMk. 4 Volkswagen Jetta Windshield And Wiper Replacement - Part 2Mk. 4 Volkswagen Jetta TDI - Turbo & Timing Belt Replacement Part 2