HOW TO: PixRacer + UBLOX NEO M8N GPS/Compass Wiring
The standard Ublox NEO M8N GPS/Compass for a Pixhawk comes with TWO plugs, BUT... the PixRacer has ONE plug. Learn how to adapt the wiring so this https://goo.gl/0Gb4Cq GPS & compass module works with YOUR PixRacer. Press SHOW MORE for the items used.
Parts Used:
-----
- UBLOX NEO M8N GPS/Compass
The GPS/Compass module used is this one:
- PixRacer
And the PixRacer can be bought here https://goo.gl/VDn9FY
What if YOUR wiring is Different?
---
Simple, at 01:01 in this video I show the wiring diagram for the PixRacer GPS port.
Even on the official board you'll have 6 wires, but 5 of them will be black and one of them is red. This tells you the orientation of the wires on this chart.
So work them according to what I've shown in the video.
The only two wires you can royally screw up is +5V & ground. Those two are obvious because one is red and the ground wire is at the opposite wire on the other end of the connector.
And before you solder up the data wires, do check it works on your PixRacer first.
As always thanks for watching & happy flying,
Matt
PS. Subscribe here for more videos like this:
https://www.youtube.com/user/moggiex/
FaceBalls Group:
https://www.facebook.com/groups/1441444805872970/
Видео HOW TO: PixRacer + UBLOX NEO M8N GPS/Compass Wiring канала RagTheNutsOff
Parts Used:
-----
- UBLOX NEO M8N GPS/Compass
The GPS/Compass module used is this one:
- PixRacer
And the PixRacer can be bought here https://goo.gl/VDn9FY
What if YOUR wiring is Different?
---
Simple, at 01:01 in this video I show the wiring diagram for the PixRacer GPS port.
Even on the official board you'll have 6 wires, but 5 of them will be black and one of them is red. This tells you the orientation of the wires on this chart.
So work them according to what I've shown in the video.
The only two wires you can royally screw up is +5V & ground. Those two are obvious because one is red and the ground wire is at the opposite wire on the other end of the connector.
And before you solder up the data wires, do check it works on your PixRacer first.
As always thanks for watching & happy flying,
Matt
PS. Subscribe here for more videos like this:
https://www.youtube.com/user/moggiex/
FaceBalls Group:
https://www.facebook.com/groups/1441444805872970/
Видео HOW TO: PixRacer + UBLOX NEO M8N GPS/Compass Wiring канала RagTheNutsOff
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
TAPE COVERING FOAMBOARD - For RC Airplane ConstructionConnecting Raspberry Pi w/ Pixhawk and Communicating via MAVLink Protocol(1/1) PixRacer - Introduction and overviewHow to Wire & Setup FPV Drone With GPS - Betaflight GPS & GPS Rescue Mode - Never Lose a Drone AgainZD550 with Pixhawk 2.4.8 buildVoltlog #146 - Is My NEO M8N GPS Module Fake?DJI Crossfire LQ in OSD How ToPart #6B - Soldering Up the NEO-M8N GPS 📡 Unit for iNav [Omnibus F4 V2]Cleanest Built Pixhawk 2.4.8 Drone | F450 frameFixed Wing Flight Controllers - Do I need a Compass?Betaflight GPS Rescue Mode - All You Need To KnowMatek F405 Wing FCB iNav setup and flightDrone Autonomous FlightPower consumption measurements of new ublox ZOE-M8B in two scenariosRMRC Rifle 2206 ReviewRC car GPS return-to-home (arduino)apm 2.8 GPS-compas m8n problemServo Pan Tilt CAMSTAB SP Racing F3/F4 on BetaFlight/CleanFlight. Setting up a Pitch Camera GimbalНастройка FlySky i6 / Turnigy i6 с 10ch Mod для APM 2.6 / 2.8