How to Add a Shower to a Claw-Foot Tub | Ask This Old House
Ask This Old House plumbing and heating expert Richard Trethewey helps a homeowner add a shower to a freestanding tub. (See below for a shopping list, tools, and steps.)
SUBSCRIBE to This Old House: http://bit.ly/SubscribeThisOldHouse
This Old House plumbing and heating expert Richard Trethewey outfits an old standalone tub with a new showerhead.
Cost: About $200 to $400
Time: 2 to 4 hours
Difficulty: Moderate. There are a surprising number of parts that must be assembled
Shopping List for How to Add a Shower to a Claw-Foot Tub:
- Chrome-plated tub-and-shower kit, including shower-curtain ring
- Copper pipe and assorted fittings
- Emery cloth, to clean copper pipe
- Lead-free solder and flux, for soldering copper pipe and fittings
- Teflon tape, to create a watertight seal on threaded fittings
- PVC primer and cement, for adhering plastic pipe and fittings
- Plumber's putty, to create a watertight seal at tub drain[BR][BR]
- Shower curtain and rings
Tools for How to Add a Shower to a Claw-Foot Tub:
- Locking pliers
- Close-quarter tubing cutter, to cut copper pipe
- Pipe brush, to clean copper pipe
- Propane torch, for soldering
- Adjustable wrench, for tightening threaded fittings
- PVC handsaw, to cut plastic pipe
- Level, for plumbing up the shower arm
- Cordless drill
Steps for How to Add a Shower to a Claw-Foot Tub:
1. Turn off the water to the bathroom at the water main or well pump.
2. Use an emery cloth to buff clean the two water-supply pipes protruding from the floor.
3. Gently pull up on the hot-water supply pipe, then clamp locking pliers onto the pipe to hold it in position. Repeat for the cold-water pipe.
4. Cut both pipes to length with a close-quarter tubing cutter.
5. Use a pipe brush to clean the inside of a copper male adapter.
6. Apply flux to the inside of the adapter and to the outside of the hot-water supply pipe.
7. Press the adapter onto the end of the pipe, then use a propane torch and lead-free solder to solder the adapter to the pipe. Repeat to solder an adapter onto the cold-water pipe.
8. Wrap the threaded portion of each adapter with Teflon tape.
9. Slide an escutcheon over each pipe, then tighten a valve onto each adapter with an adjustable wrench. Release the locking pliers.
10. Turn the water back on and check for leaks.
11. Use a PVC handsaw to cut the plastic drainpipe slightly below the surface of the finished floor.
12. Adhere a PVC fitting onto the end of the drainpipe with PVC primer and cement.
13. Set the chrome-plated escutcheon over the fitting.
14. Wrap a rope of plumber's putty around the threaded portion of the tub's drain fitting.
15. Assemble and connect the tub's drainpipe and overflow tube.
16. Install the new faucet to the tub wall, then connect both the hot- and cold-water supply pipes.
17. Tighten the showerhead onto the shower arm, then mount the shower arm to the tub faucet.
18. Attach an adjustable ceiling bracket to the shower arm.
19. Use a level to hold the shower arm perfectly plumb (vertical), then screw the bracket to the ceiling.
20. Connect the shower-curtain ring to the shower arm, then suspend the ring from the ceiling with vertical supports.
21. Install a shower curtain to the ring.
22. Attach a handheld showerhead to the tub faucet.
About Ask This Old House TV:
Homeowners have a virtual truckload of questions for us on smaller projects, and we're ready to answer. Ask This Old House solves the steady stream of home improvement problems faced by our viewers—and we make house calls! Ask This Old House features some familiar faces from This Old House, including Kevin O'Connor, general contractor Tom Silva, plumbing and heating expert Richard Trethewey, and landscape contractor Roger Cook
Looking for more step by step guidance on how to complete projects around the house? Join This Old House INSIDER to stream over 1,000 episodes commercial-free: https://bit.ly/2GPiYbH
Plus, download our FREE app for full-episode streaming to your connected TV, phone or tablet:
https://bit.ly/34RYEP5
Follow This Old House and Ask This Old House:
Facebook: http://bit.ly/ThisOldHouseFB
Twitter: http://bit.ly/ThisOldHouseTwitter
http://bit.ly/AskTOHTwitter
Pinterest: http://bit.ly/ThisOldHousePinterest
Instagram: http://bit.ly/ThisOldHouseIG
http://bit.ly/AskTOHIG
For more on This Old House and Ask This Old House, visit us at: http://bit.ly/ThisOldHouseWebsite
How to Add a Shower to a Claw-Foot Tub | Ask This Old House
https://www.youtube.com/user/thisoldhouse/
Видео How to Add a Shower to a Claw-Foot Tub | Ask This Old House канала This Old House
SUBSCRIBE to This Old House: http://bit.ly/SubscribeThisOldHouse
This Old House plumbing and heating expert Richard Trethewey outfits an old standalone tub with a new showerhead.
Cost: About $200 to $400
Time: 2 to 4 hours
Difficulty: Moderate. There are a surprising number of parts that must be assembled
Shopping List for How to Add a Shower to a Claw-Foot Tub:
- Chrome-plated tub-and-shower kit, including shower-curtain ring
- Copper pipe and assorted fittings
- Emery cloth, to clean copper pipe
- Lead-free solder and flux, for soldering copper pipe and fittings
- Teflon tape, to create a watertight seal on threaded fittings
- PVC primer and cement, for adhering plastic pipe and fittings
- Plumber's putty, to create a watertight seal at tub drain[BR][BR]
- Shower curtain and rings
Tools for How to Add a Shower to a Claw-Foot Tub:
- Locking pliers
- Close-quarter tubing cutter, to cut copper pipe
- Pipe brush, to clean copper pipe
- Propane torch, for soldering
- Adjustable wrench, for tightening threaded fittings
- PVC handsaw, to cut plastic pipe
- Level, for plumbing up the shower arm
- Cordless drill
Steps for How to Add a Shower to a Claw-Foot Tub:
1. Turn off the water to the bathroom at the water main or well pump.
2. Use an emery cloth to buff clean the two water-supply pipes protruding from the floor.
3. Gently pull up on the hot-water supply pipe, then clamp locking pliers onto the pipe to hold it in position. Repeat for the cold-water pipe.
4. Cut both pipes to length with a close-quarter tubing cutter.
5. Use a pipe brush to clean the inside of a copper male adapter.
6. Apply flux to the inside of the adapter and to the outside of the hot-water supply pipe.
7. Press the adapter onto the end of the pipe, then use a propane torch and lead-free solder to solder the adapter to the pipe. Repeat to solder an adapter onto the cold-water pipe.
8. Wrap the threaded portion of each adapter with Teflon tape.
9. Slide an escutcheon over each pipe, then tighten a valve onto each adapter with an adjustable wrench. Release the locking pliers.
10. Turn the water back on and check for leaks.
11. Use a PVC handsaw to cut the plastic drainpipe slightly below the surface of the finished floor.
12. Adhere a PVC fitting onto the end of the drainpipe with PVC primer and cement.
13. Set the chrome-plated escutcheon over the fitting.
14. Wrap a rope of plumber's putty around the threaded portion of the tub's drain fitting.
15. Assemble and connect the tub's drainpipe and overflow tube.
16. Install the new faucet to the tub wall, then connect both the hot- and cold-water supply pipes.
17. Tighten the showerhead onto the shower arm, then mount the shower arm to the tub faucet.
18. Attach an adjustable ceiling bracket to the shower arm.
19. Use a level to hold the shower arm perfectly plumb (vertical), then screw the bracket to the ceiling.
20. Connect the shower-curtain ring to the shower arm, then suspend the ring from the ceiling with vertical supports.
21. Install a shower curtain to the ring.
22. Attach a handheld showerhead to the tub faucet.
About Ask This Old House TV:
Homeowners have a virtual truckload of questions for us on smaller projects, and we're ready to answer. Ask This Old House solves the steady stream of home improvement problems faced by our viewers—and we make house calls! Ask This Old House features some familiar faces from This Old House, including Kevin O'Connor, general contractor Tom Silva, plumbing and heating expert Richard Trethewey, and landscape contractor Roger Cook
Looking for more step by step guidance on how to complete projects around the house? Join This Old House INSIDER to stream over 1,000 episodes commercial-free: https://bit.ly/2GPiYbH
Plus, download our FREE app for full-episode streaming to your connected TV, phone or tablet:
https://bit.ly/34RYEP5
Follow This Old House and Ask This Old House:
Facebook: http://bit.ly/ThisOldHouseFB
Twitter: http://bit.ly/ThisOldHouseTwitter
http://bit.ly/AskTOHTwitter
Pinterest: http://bit.ly/ThisOldHousePinterest
Instagram: http://bit.ly/ThisOldHouseIG
http://bit.ly/AskTOHIG
For more on This Old House and Ask This Old House, visit us at: http://bit.ly/ThisOldHouseWebsite
How to Add a Shower to a Claw-Foot Tub | Ask This Old House
https://www.youtube.com/user/thisoldhouse/
Видео How to Add a Shower to a Claw-Foot Tub | Ask This Old House канала This Old House
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
How to Add a Shower to a Claw-Foot Tub | This Old HouseReplacing a Kitchen Sink | Ask This Old House100 Year Old Clawfoot Tub ~~ REFINISHEDClawfoot Tub Restoration - DuraFinish Inc.How to Repair a Squealing Shower | Ask This Old HouseDIY How to Renovate the Tub / Shower from A to ZEasy Freestanding Tub Installation - WHY YOU NEED THIS!!! - Island Tub DrainEasy way to Install a Freestanding Tub- Part 2ASK This Old House | Weird Shower Valve, Mossy Roof (S18 E14) FULL EPISODEBathroom Remodel Tips and Tricks!How to Upgrade a Bathroom Vanity | Ask This Old HouseHow to Replace a Kitchen Sink Strainer | Ask This Old HouseHow to Install a Fire Escape Ladder | Ask This Old House1920s Kohler Clawfoot Tub (Building Farmhouse #20)How to Repair a Damaged Carrying Beam | Ask This Old HouseHow To Install a Clawfoot TubThis Old House | Brick and Mortar (S39 E19) | FULL EPISODEA Vintage Clawfoot Tub Makeover with Maison Blanche PaintsHow to Rotate a Toilet | Ask This Old HouseClawfoot tub shower curtain improvement | Shower curtain rod for clawfoot tub