How to Make a Flat Bend (90 Degree Bend) in 50 x 50 Steel Trunking for C and G 5357 Assessment
How to make a flat bend in 50 x 50 steel trunking. This is a full demonstration on how to make a 90 degree bend in steel trunking which is a requirement of the City and Guilds 5357 practical assessment 107.
Using The City and Guilds Textbook Book 1 for the 5357.
Understand and Carry Out Terminations and Connections of Conductors 5357 107.
Note the song from 12:51 to 13:21 has been removed hence the silence thanks Gaz
Videos are training aids for City and Guilds (C and G) and EAL courses Level 1, 2 and 3.
You can follow me day by day on Facebook, Instagram and Twitter lookout for "GSH Electrical.
▶️ FACEBOOK https://www.facebook.com/gshelectrical/
▶️ INSTAGRAM https://instagram.com/p/BrIhZmrAYGDTmjMdb9lUNQodMevqsbDDki3qpQ0/
▶️ TWITTER https://mobile.twitter.com/gsh_electrical
#GSHElectrical #Electricaltrainingvideos
Видео How to Make a Flat Bend (90 Degree Bend) in 50 x 50 Steel Trunking for C and G 5357 Assessment канала GSH Electrical
Using The City and Guilds Textbook Book 1 for the 5357.
Understand and Carry Out Terminations and Connections of Conductors 5357 107.
Note the song from 12:51 to 13:21 has been removed hence the silence thanks Gaz
Videos are training aids for City and Guilds (C and G) and EAL courses Level 1, 2 and 3.
You can follow me day by day on Facebook, Instagram and Twitter lookout for "GSH Electrical.
▶️ FACEBOOK https://www.facebook.com/gshelectrical/
▶️ INSTAGRAM https://instagram.com/p/BrIhZmrAYGDTmjMdb9lUNQodMevqsbDDki3qpQ0/
▶️ TWITTER https://mobile.twitter.com/gsh_electrical
#GSHElectrical #Electricaltrainingvideos
Видео How to Make a Flat Bend (90 Degree Bend) in 50 x 50 Steel Trunking for C and G 5357 Assessment канала GSH Electrical
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
How to Bend Steel Conduit to the Correct Measurement from the End of the Conduit to Back of the BendHow to Make off a SWA Cable Gland (Steel Wire Armored Cable) Step By Step DemonstrationHow to band 45° x 45° electrical trunking90 degree trunking bend with formula and measurment | how to modify trunking 90 degreeElectricians day Consumer unit change. Uncovering poor workmanship !!!How to Make an Internal Bend in Steel Cable Tray Using a Crimping Tool or Bending MachineHow to put a Double Set (offset) into Steel Conduit Using a Conduit Bending Machine (EMT)How to Bend and Cut 20 mm PVC Conduit (90 Degrees Bend Using a Bending Spring)How to Fix the Lid to 50 x 50mm Galvanised Steel Trunking Using Trunbuckle Clips (Read Description)John Ward Talks About Old Consumer Units (Fuse Boards), Old Fuses, VIR and Lead Sheathed CablesHow to make custom patch panels with ease.Steel Trunking Installation - Electricians Race The ClockHow to easily make a small radius bend in flat steel - general fabrication tipTrunking offset (45) formula and measurment |learn offset formula |Mr electrationHow to Cut and Thread Steel Conduit so a Coupler or Spouted box can be Fitted (Metal Conduit 20mm)Electrical Practical Skills Bending a Crank Set in Steel Conduit (How to Make bubble set or bridge)Step by Step Guide on How to Bend Steel Conduit Back of Bend to Back of Bend (AM2 AM2s)how to cut pvc trunking 90 degreeWorking with steel trunking