Ergodox Build
I build an ergodox keyboard using a 3D printed frame.
Parts list:
1x Pair of pcbs (one for each hand)
1x Teensy USB Board, Version 2.0
24x Teensy header pins, male (unless pre-installed)
1x MCP23018-E/SP I/O expander
76-80x Cherry MX switches, (depending on your layout)
76-80x 1N4148 diodes, SOD-123 package (Surface mount) or DO-35,(0.3” pitch) (through hole) (again, the amount needed will depend on your layout)
2x 2.2k Ω resistors (red, red, red)
3x 3mm T1 LEDs
3x 220 Ω resistors, or match to LED. (red, red, brown)
5x Short jumpers (You can also use the clipped off legs from your resistors)
1x 0.1 µF ceramic capacitor (marked “104” for 10*104 picofarad). Not strictly necessary but suggested
1x USB mini B connector WM17115
1x USB mini B plug with short cable (such as H2955)
1x USB cable male A to male mini B
2x 3.5 mm TRRS sockets, CP-43514. FC68129 will also work if its extra pins are snipped off
1x Cable with two 3.5 mm TRRS plugs
76-80x MX Keycaps
All parts found on:
https://kono.store/ (MX Switches)
https://www.amazon.com/ (PCB and Teensy 2.0)
https://www.digikey.com/en/resources/beta (all other parts)
Watch these other channels I like:
https://www.youtube.com/user/MandaloreGaming
https://www.youtube.com/channel/UCMrMVIBtqFW6O0-MWq26gqw
https://www.youtube.com/user/reppesis
Видео Ergodox Build канала smarmy_builds
Parts list:
1x Pair of pcbs (one for each hand)
1x Teensy USB Board, Version 2.0
24x Teensy header pins, male (unless pre-installed)
1x MCP23018-E/SP I/O expander
76-80x Cherry MX switches, (depending on your layout)
76-80x 1N4148 diodes, SOD-123 package (Surface mount) or DO-35,(0.3” pitch) (through hole) (again, the amount needed will depend on your layout)
2x 2.2k Ω resistors (red, red, red)
3x 3mm T1 LEDs
3x 220 Ω resistors, or match to LED. (red, red, brown)
5x Short jumpers (You can also use the clipped off legs from your resistors)
1x 0.1 µF ceramic capacitor (marked “104” for 10*104 picofarad). Not strictly necessary but suggested
1x USB mini B connector WM17115
1x USB mini B plug with short cable (such as H2955)
1x USB cable male A to male mini B
2x 3.5 mm TRRS sockets, CP-43514. FC68129 will also work if its extra pins are snipped off
1x Cable with two 3.5 mm TRRS plugs
76-80x MX Keycaps
All parts found on:
https://kono.store/ (MX Switches)
https://www.amazon.com/ (PCB and Teensy 2.0)
https://www.digikey.com/en/resources/beta (all other parts)
Watch these other channels I like:
https://www.youtube.com/user/MandaloreGaming
https://www.youtube.com/channel/UCMrMVIBtqFW6O0-MWq26gqw
https://www.youtube.com/user/reppesis
Видео Ergodox Build канала smarmy_builds
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
![Ergo-Dox keyboard assembly](https://i.ytimg.com/vi/x1irVrAl3Ts/default.jpg)
![Ergodox EZ ergonomic keyboard build: making it thock (๑˃ᴗ˂)ﻭ | ft. Gateron milky yellow switch.](https://i.ytimg.com/vi/q4azWtAHdcA/default.jpg)
![DILLY Choc/olate Mechanical Keyboard Build](https://i.ytimg.com/vi/1yP-3AFCBWg/default.jpg)
![CMD - Dactyl Manuform Build](https://i.ytimg.com/vi/CxNKWNKBLMs/default.jpg)
![ErgoDox Build (w/ Costar stabilizers)](https://i.ytimg.com/vi/2EBkfbGn6KA/default.jpg)
![Hand Wired Dactyl Manuform Keyboard Build Log #1: Introduction , Rows, and Diodes](https://i.ytimg.com/vi/UerP5bxGL3c/default.jpg)
![I Have Waited A LONG TIME for this keyboard!!! - ZSA Moonlander](https://i.ytimg.com/vi/_72cQVOqINI/default.jpg)
![3D Printed PLA Gear after 2 Years? - Spur Gear Tool in Fusion360](https://i.ytimg.com/vi/vuJmWKsCYcU/default.jpg)
![Keyboard Build Stream - Dactyl Manuform - Part 2](https://i.ytimg.com/vi/fDc6rjZGYiI/default.jpg)
![P4: Fully DIY Mechanical Keyboard (Code name: Arke)| Wiring & Firmware | Part 3](https://i.ytimg.com/vi/7Ky9WOvL2Ns/default.jpg)
![Professional SMT Soldering: Hand Soldering Techniques - Surface Mount](https://i.ytimg.com/vi/5uiroWBkdFY/default.jpg)
![Make a Cheap 3D Printer Better - Anet A8 Print Quality Upgrades](https://i.ytimg.com/vi/7SAEUajLPW4/default.jpg)
![Make Money 3D Printing in 2021 | Over $100K Per Year](https://i.ytimg.com/vi/gKDDoSryluo/default.jpg)
![Making of PCBs at home, DIY using inexpenive materials](https://i.ytimg.com/vi/mv7Y0A9YeUc/default.jpg)
![Keyboard Build Stream - Dactyl Manuform - Part 1](https://i.ytimg.com/vi/dWC_8BOArzc/default.jpg)
![I Split My Keyboard In Half To Write Code. Worth It?](https://i.ytimg.com/vi/4YZ0PWvIXGY/default.jpg)
![DIY Printed circuit board](https://i.ytimg.com/vi/wKEe3otWstM/default.jpg)
![I used a split keyboard for 30 days](https://i.ytimg.com/vi/wPGmZXAQRyw/default.jpg)
![Building the Infinity ErgoDox DIY Keyboard Kit!](https://i.ytimg.com/vi/eI1m-rJ3bGY/default.jpg)
![Insane Ergonomic & Split Keyboard - Ergodox EZ Build and Review](https://i.ytimg.com/vi/CBF0Ho_sF-c/default.jpg)