Om617 knocking/rattling noise, injector nailing before and after nozzle replacement
Replaced the injector nozzles on my 82 W123 Mercedes 300D in hopes of quieting down a strange metallic knock/rattle/ping I was concerned could be rod knock.
This engine was run for an unknown time with low oil pressure due to not having any oil in it thanks to the turbo drain leaking, which started flattening a lobe on the cam, and froze up the bearing on the vacuum pump.
I caught both just in time as there was no real metal fragments or anything seemingly wrong from a visual analysis of the oil. It had a strange little tapping noise, I tried a different set of injectors I pulled from a car in a junkyard, Wasn't smart enough to replace crush washers, seemed to help a little so we drove the car for quite some time, have done a few oil changes and that little pinging knocking sound hasn't ever really gotten worse but it hasn't seemed to go away either.
Decided to dig in and see what I could find.
We nearly immediately after making this video took the car about 100 miles, It seems the injectors are settling in very nicely, the car has quieted down and smoothed out quite a lot from where it was in this video.
Check your injectors, especially if they've never been serviced/rebuilt!
Key things in video:
0:00 Introduction
1:06 Starting engine before, listening to the noise, noticing bubbling from cyl2
2:16 Removing injectors to investigate the bubbling
3:25 Finding cyl2 injector wet and covered in carbon buildup
3:40 Cyl1 has carbon built up on one side of heat shield and around prechamber slightly
4:14 Some footage from pop-testing to show difference between a very bad injector (cyl2) and a decent injector (cyl3)
5:40 Crush washer was barely contacting cyl2 injector.
7:00 Rebuilding injector video coming later, In meantime, New DN0SD314 nozzles (Larger than stock = More power?)
7:30 Cleaning injector threads and crush washer mating surface in head with small brass brush
8:15 Installing new crush washers
9:00 Torquing injectors into head
11:05 All back together, bleeding air out of injector lines
11:25 Running on new injectors
11:50 Before and After comparisons
12:14 Test drive
13:00 Closing thoughts
Links to products used in this video: (These may be affiliate links so that I get a small commission if you choose to purchase any of these items from these links)
ACDelco Torque adapter: https://amzn.to/2BTcnap
Powerbuilt 27mm Deep socket: https://amzn.to/2NoPFfG
Firad DN0SD314 Nozzles (One size larger than stock): https://www.idparts.com/firad-injector-nozzle-sd-314-p-3085.html
Firad DN0SD265 Nozzles (Stock Nozzles): https://www.idparts.com/firad-sd265-injector-nozzle-om616-om617-om601-om602-om603-p-3084.html
Crush washers: https://www.idparts.com/injector-heat-shield-ring-om616-om606-om617-om602-om603-p-3118.html
Things you need to use the gigantic primary "prefilter" that I have:
Filter housing: https://amzn.to/31lon0T
Mesh filter: https://amzn.to/39VP14r
Fittings: https://amzn.to/2XqYBHq
3/8 fuel line: https://amzn.to/3gtDdZy
Clamps for fuel line: https://amzn.to/31mavUd
Видео Om617 knocking/rattling noise, injector nailing before and after nozzle replacement канала trythistv
This engine was run for an unknown time with low oil pressure due to not having any oil in it thanks to the turbo drain leaking, which started flattening a lobe on the cam, and froze up the bearing on the vacuum pump.
I caught both just in time as there was no real metal fragments or anything seemingly wrong from a visual analysis of the oil. It had a strange little tapping noise, I tried a different set of injectors I pulled from a car in a junkyard, Wasn't smart enough to replace crush washers, seemed to help a little so we drove the car for quite some time, have done a few oil changes and that little pinging knocking sound hasn't ever really gotten worse but it hasn't seemed to go away either.
Decided to dig in and see what I could find.
We nearly immediately after making this video took the car about 100 miles, It seems the injectors are settling in very nicely, the car has quieted down and smoothed out quite a lot from where it was in this video.
Check your injectors, especially if they've never been serviced/rebuilt!
Key things in video:
0:00 Introduction
1:06 Starting engine before, listening to the noise, noticing bubbling from cyl2
2:16 Removing injectors to investigate the bubbling
3:25 Finding cyl2 injector wet and covered in carbon buildup
3:40 Cyl1 has carbon built up on one side of heat shield and around prechamber slightly
4:14 Some footage from pop-testing to show difference between a very bad injector (cyl2) and a decent injector (cyl3)
5:40 Crush washer was barely contacting cyl2 injector.
7:00 Rebuilding injector video coming later, In meantime, New DN0SD314 nozzles (Larger than stock = More power?)
7:30 Cleaning injector threads and crush washer mating surface in head with small brass brush
8:15 Installing new crush washers
9:00 Torquing injectors into head
11:05 All back together, bleeding air out of injector lines
11:25 Running on new injectors
11:50 Before and After comparisons
12:14 Test drive
13:00 Closing thoughts
Links to products used in this video: (These may be affiliate links so that I get a small commission if you choose to purchase any of these items from these links)
ACDelco Torque adapter: https://amzn.to/2BTcnap
Powerbuilt 27mm Deep socket: https://amzn.to/2NoPFfG
Firad DN0SD314 Nozzles (One size larger than stock): https://www.idparts.com/firad-injector-nozzle-sd-314-p-3085.html
Firad DN0SD265 Nozzles (Stock Nozzles): https://www.idparts.com/firad-sd265-injector-nozzle-om616-om617-om601-om602-om603-p-3084.html
Crush washers: https://www.idparts.com/injector-heat-shield-ring-om616-om606-om617-om602-om603-p-3118.html
Things you need to use the gigantic primary "prefilter" that I have:
Filter housing: https://amzn.to/31lon0T
Mesh filter: https://amzn.to/39VP14r
Fittings: https://amzn.to/2XqYBHq
3/8 fuel line: https://amzn.to/3gtDdZy
Clamps for fuel line: https://amzn.to/31mavUd
Видео Om617 knocking/rattling noise, injector nailing before and after nozzle replacement канала trythistv
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
03 Cummins 5.9L Hard Knock DiagnosisFuel Injection cleaning in less than 5 Minutes/HOW TO clean injection Directly without disassemblingEngine Ticking Free Fix Must Watch For ALL Car Owners NO LIQUIDS USED Hydraulic Lifter TickCommon Problems with Common Rail Injector, Diesel Fuel Injector Failed, Symptoms, Diesel Tech TipsEngine noise testing hyundai i20 dieselI hear you knocking! 300Tdi came in with a bad knock - what could it be?Volvo c30 D2 1.6 diesel, strange noise on acceleration, rattle.ENGINE KNOCKING NOISE DIAGNOSE AND FIXDiesel Engine Maintenance Tip 6: Troubleshooting Unhealthy Engine SoundsDiagnosing Early Mercedes Diesel No Start, Rough Running, Heavy Smoke Problems - Part 1How to Diagnose, Test and Clean Dirty, Clogged or Bad Fuel Injectors(SOLVED)Engine Knocking or Tapping Sound That Varied With RPMLIQUI-MOLY Diesel Purge | Does it actually clean injectors? | Injector Feedback Test -Fuel injection93 w140 Mercedes Benz replace injector nozzle.Testing Fuel Injectors FastBlowby What is normal and what is not?Replacing GM 6.5 Diesel Injectors - Knock Fixed? [C3500HD Part 2]Mercedes 300 Diesel OM617 912 start after being parked for a long timeWhat Causes Diesel Engine Ticking, Clicking, Tapping, and Knocking?Mercedes 300SD W126 - OM617 Injector Nozzle Replacement/Upgrade