DIY Milling Machine
For years I've always wanted a milling machine but they are too expensive and I just couldn't bring myself to pony up to dosh. So I decided to make one myself out of spare parts I had laying around, the results are pretty amazing.
It's not an industrial machine and it seems to work fine making small cuts - perfect for my needs.
Parts used:
Centre Pole and lead screw:
The centre pole is from an old bench grinder pedestal I salvaged from a scrap yard, I machined it and used it as my centre stand, the lead screw was some threaded bar purchased from Bunnings.
Bearings: 30mm flanged bearings, purchased from e-Bay
Motors:
For the table X axis I used a window washer motor from a small car connected to a 12v motor speed controller for the power feed, for the clutch I used a 19mm socket and machines a square to easily engage and disengage the power feed.
For the head I used a hydraulic paint sprayer pump 2400watt motor which I picked up form a recycling centre for cheap.
For the Z axis I used the rise / fall motor out of a treadmill, this motor was perfect as it was already geared to lift a heavy load.
Parts Purchased
Bed: Compound table 155x470mm purchased from Hare and Forbes https://www.machineryhouse.com.au/M198?gclid=Cj0KCQiAk7TuBRDQARIsAMRrfUZDpIP4tFT3oNsCCXEOw2WxM4OmxyVrGBjtrPzMFFd75TmTdtcFor8aAl9JEALw_wcB
Pillow Block Bearing UCF207 35mm https://rover.ebay.com/rover/1/711-5...item521a81bdc0
4" Milling Machinist Vise https://rover.ebay.com/rover/1/711-5...72.m2749.l2658
ER32 Collet Set https://rover.ebay.com/rover/1/711-5...72.m2749.l2649
M3 Face Milling Cutter https://rover.ebay.com/rover/1/711-5...refresh%3Dtrue
ER32 Collet Set https://rover.ebay.com/rover/1/711-5...72.m2749.l2649
Additional information about the build and parts used is located using the links below.
Homemadetools forum https://www.homemadetools.net/forum/diy-milling-machine-74852
Hackaday forum https://hackaday.com/2019/09/01/scrapyard-milling-machine-gets-work-done-on-a-budget/#comment-6176735
Видео DIY Milling Machine канала Maximum DIY
It's not an industrial machine and it seems to work fine making small cuts - perfect for my needs.
Parts used:
Centre Pole and lead screw:
The centre pole is from an old bench grinder pedestal I salvaged from a scrap yard, I machined it and used it as my centre stand, the lead screw was some threaded bar purchased from Bunnings.
Bearings: 30mm flanged bearings, purchased from e-Bay
Motors:
For the table X axis I used a window washer motor from a small car connected to a 12v motor speed controller for the power feed, for the clutch I used a 19mm socket and machines a square to easily engage and disengage the power feed.
For the head I used a hydraulic paint sprayer pump 2400watt motor which I picked up form a recycling centre for cheap.
For the Z axis I used the rise / fall motor out of a treadmill, this motor was perfect as it was already geared to lift a heavy load.
Parts Purchased
Bed: Compound table 155x470mm purchased from Hare and Forbes https://www.machineryhouse.com.au/M198?gclid=Cj0KCQiAk7TuBRDQARIsAMRrfUZDpIP4tFT3oNsCCXEOw2WxM4OmxyVrGBjtrPzMFFd75TmTdtcFor8aAl9JEALw_wcB
Pillow Block Bearing UCF207 35mm https://rover.ebay.com/rover/1/711-5...item521a81bdc0
4" Milling Machinist Vise https://rover.ebay.com/rover/1/711-5...72.m2749.l2658
ER32 Collet Set https://rover.ebay.com/rover/1/711-5...72.m2749.l2649
M3 Face Milling Cutter https://rover.ebay.com/rover/1/711-5...refresh%3Dtrue
ER32 Collet Set https://rover.ebay.com/rover/1/711-5...72.m2749.l2649
Additional information about the build and parts used is located using the links below.
Homemadetools forum https://www.homemadetools.net/forum/diy-milling-machine-74852
Hackaday forum https://hackaday.com/2019/09/01/scrapyard-milling-machine-gets-work-done-on-a-budget/#comment-6176735
Видео DIY Milling Machine канала Maximum DIY
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
Making Cross TableMilling Machine homemade (Z AXIS - COLUMN) - Part 2🗜️I build coordinate table in 3 days 🗜️ Construyo FRESADORA /Mesa de Coordenadas a mi taladroHomemade Lathe MachineBuilding a vertical mill from industrial scrapMaking Lathe MILLING AttachmentMaking of face milling tool - 200mm diameter - The Fly Cutter × 4The Cheapest CNC Milling MachineBuilding my own CNC MillHomemade Milling Machine (X and Y axis)HOME MADE MILLING MACHINE FROM GARBAGE MATERIALS! PART 1Cheap Chinese Mini Metal Mill Milling Machine Unboxing, Setup, Testing, and ReviewHow to make a real drill press! Benchtop drill machine makingDIY gear hobbing attachment for milling machine (part 1)Homemade Milling MachineHorizontal to vertical Milling machineDIY Milling Machine Build [Based on Bridgeport]. Part 1: SpindleBuilding a lathe from industrial scrapCheap Drill Press converted to Milling MachineHomemade Lathe Machines, Highlights homemade lathes #HomemadeMetalLathe #DIYLathe