Braava Jet M6 Review - Full evaluation with Roomba Integration
Today I will be evaluating the Irobot Brava jet M6 which allows for automation integration with the Roomba I7, a vacuum which we already own. Our house is entirely tiled except for rugs, no carpeted rooms. So a quick unboxing is conducted and we jump right into it.
I would have like to have seen an auto filling station for the cleaning agent, much like the I7 has for removing dirt for the unit. I can see how adding cleaning fluid every few uses does speak well to automation.
The same app for our other device allows adding this mop, same procedure. Just like the vacuum, I conduct a mapping run. It builds a separate map, since it does not run on carpet. It can however run over carpet via configuration to reach areas of the house as needed.
At first we got off to a shaky start, but it gets smarter at subsequent re-attempts. Once the map was completed the mop fitting was added and cleaning solution was mixed to the correct values with water and filled.
The float can get stuck in the container and give a false indication of empty when it is fact not. I found this to be true as well. A gentle shake can fix this. Like the other roomba it does not work near the dock, the full house clean does a special care clean by the dock area.
The tread mark complaints were only witnessed when the device was brand new but cleared.
Consumption settings should be checked and set, how much spray is used to clean could be the difference substantially between fillings. Again, an auto fill station would be grand.
Integration settings in software is good. Ours starts after vacuuming finishes. That said, its good for light moping, I wouldnt use this as the commercial shows, cleaning up spilled milk in a kitchen, what would be a disaster after a few hours back on the dock. But a great compliment to the vacuum cleaner.
iRobot Authentic Replacement Parts- Braava jet m Series Washable Wet Mopping Pads, (2-Pack)
https://amzn.to/3llEWYC
#irobot #braava
Видео Braava Jet M6 Review - Full evaluation with Roomba Integration канала Retro Tech & Electronics
I would have like to have seen an auto filling station for the cleaning agent, much like the I7 has for removing dirt for the unit. I can see how adding cleaning fluid every few uses does speak well to automation.
The same app for our other device allows adding this mop, same procedure. Just like the vacuum, I conduct a mapping run. It builds a separate map, since it does not run on carpet. It can however run over carpet via configuration to reach areas of the house as needed.
At first we got off to a shaky start, but it gets smarter at subsequent re-attempts. Once the map was completed the mop fitting was added and cleaning solution was mixed to the correct values with water and filled.
The float can get stuck in the container and give a false indication of empty when it is fact not. I found this to be true as well. A gentle shake can fix this. Like the other roomba it does not work near the dock, the full house clean does a special care clean by the dock area.
The tread mark complaints were only witnessed when the device was brand new but cleared.
Consumption settings should be checked and set, how much spray is used to clean could be the difference substantially between fillings. Again, an auto fill station would be grand.
Integration settings in software is good. Ours starts after vacuuming finishes. That said, its good for light moping, I wouldnt use this as the commercial shows, cleaning up spilled milk in a kitchen, what would be a disaster after a few hours back on the dock. But a great compliment to the vacuum cleaner.
iRobot Authentic Replacement Parts- Braava jet m Series Washable Wet Mopping Pads, (2-Pack)
https://amzn.to/3llEWYC
#irobot #braava
Видео Braava Jet M6 Review - Full evaluation with Roomba Integration канала Retro Tech & Electronics
Показать
Комментарии отсутствуют
Информация о видео
28 августа 2021 г. 18:06:20
00:10:32
Другие видео канала
Tektronix AN/USM-488 2235 Oscilloscope repair and calibration 7 of 7VW Buggy Carb swap-out setup and testFREEDV digital voice over HF single sidebandFeeltech FY3200S FY3224S - Amplitude modulated waveform versus RF signal generator TSG17Innovate LM-2 New RPM signal locationMaxair Vstar 1100 Innovate LM-2 Roadtest- Front CYL 1 of 2Linux FLDIGI to the Yaesu FT817 Tutorial - Part 2 - Audio ConfigurationPort-o-matic - The Antique IPOD of the 1930's - Repair project Part 1Roberts Reel to Reel Model 1725 RestorationFT817OS Restoring the Calibration SettingsAntique SNAP-ON MT665 Automotive Analyzer Repair - 4 of 9 HV Tripler RebuildWelcome to Jordan Rubin's YouTube channel...Using an interrupt from TOD clock for Binary counterOriginal trailer for the channelHP 331A Distortion analyzer repair and calibration Mini DocumentaryMaxair lean issue solved [before] on LM-2 VSTAR 1100 (bad diaphragm circuit)Ham radio - FREEDV decode from the qso from the distant endSears Silvertone Twin Twelve 1484 Major Restoration Project [5/6]Tennessee Valley Railroad Museum - Locomotive Adventure - Missionary RidgeHeathkit Repair - Regulated Power Supply IP-20 Part 3 of 3ESP32 Automated Irrigation Control System Project - PART 3 - The main Sprinkler Class