TP4056 Charger 18650 Baterai BMS 1S┃ Paralel TP4056 protection

@Radal 05
Video ini hanya test modul TP4056 dipasang secara paralel.

0:00 radal05
0:10 TP4056 dan tp4056 protection
0:50 Spesifikasi TP4056
2:29 Spesifikasi tp4056 protection
4:40 Tegangan output TP4056
5:30 Tes tp4056
7:05 Paralel TP4056
8:00 Kesimpulan

FEATURES
· Programmable Charge Current Up to 1000mA
·No MOSFET, Sense Resistor or Blocking Diode Required
· Complete Linear Charger in SOP-8 Package for Single Cell Lithium-Ion
Batteries
·Constant-Current/Constant-Voltage ·Charges Single Cell Li-Ion Batteries Directly from USB Port
·Preset 4.2V Charge Voltage with 1.5%
Accuracy
·Automatic Recharge
·two Charge Status Output Pins
·C/10 Charge Termination
·2.9V Trickle Charge Threshold (TP4056)
·Soft-Start Limits Inrush Current
·Available Radiator in 8-Lead SOP Package,
the Radiator need connect GND or
impending

Features:
Programmable Charge Current Up to 1000mA
No MOSFET, Sense Resistor or Blocking Diode Required
Complete Linear Charger in SOP-8 Package for Single Cell Lithium-Ion Batteries
Constant-Current/Constant-Voltage
Charges Single Cell Li-Ion Batteries Directly from USB Port
Preset 4.2V Charge Voltage with 1.5% Accuracy
Automatic Recharge
two Charge Status Output Pins
C/10 Charge Termination
2.9V Trickle Charge Threshold (TP4056)
Soft-Start Limits Inrush Current
Available Radiator in 8-Lead SOP Package, the Radiator need connect GND or impending
Specification:

Charge Controller: TP4056
Protection IC: DW01A or DW01P
Charge Method: Constant-Current/Constant-Voltage (CC/CV)
Charge/Discharge Control MOSFET: FS8205A
The input voltage via microUSB or miniUSB: 5V
Input voltage via solder pads on left-hand side of module: 4.5V~5.5V
Charging current: 1A by default. However you can change this by changing the 1k2 resistor next to the "IN-" pad the bottom-left of the board. See the Rprog table on page three of the TP4056 data sheet for different values and matching charging currents. The "current resistor" can be replaced for other (lower) charge currents, because it is a 0603 size smd resistor (i.e. very small) it can be difficult to replace it. With the mounted resistor the charger can handle larger batteries, but changing the resistor makes it possible to charge smaller batteries.
Charging indicator: Red LED, green or blue LED
Interface: Mini USB or Micro USB
Charge Complete (Float) Voltage 4.2 V ±1.5%
Overcharge Detection Voltage 4.3 V ±50 mV
Overcharge Release Voltage 4.1 V ±50 mV
Over-Discharge Detection Voltage 2.4 V ±100 mV
Over-Discharge Release Voltage 3.0 V ±100 mV
Overcurrent Protection Threshold 3 A
Overcurrent Cutout Delay 10~20 ms
Short-Circuit Cutout Delay 5~50 µs
Trickle Charge (Battery Reconditioning)
Trickle Charge Threshold Voltage 2.9 V ±0.1 V
Trickle Charge Current 130 mA ±10 mA
Application:
Cellular Telephones, PDAs, GPS;
Charging Docks and Cradles;
Digital Still Cameras, Portable Devices;
USB Bus-Powered Chargers,Chargers.

Видео TP4056 Charger 18650 Baterai BMS 1S┃ Paralel TP4056 protection канала Radal 05