How the Air Dryer Works to Pass CDL Air Brake Pre-Trip Inspection Test
The air dryer filters moisture and other contaminants from the compressed air in the air brake system - watch the video! CDL IN-CAB Air Brake CHECKLIST: https://www.smartdrivetest.com/cdl-air-brake-checklist SUBSCRIBE TODAY! ► http://youtube.com/c/smartdrivetest
Get 30% OFF Air Brake Course. Coupon "youtube30" CLICK THE LINK https://www.smartdrivetest.com/pass-cdl-air-brakes-course SEE TOPICS BELOW.
Get 25% OFF Air Brake Course. CLICK THE LINK https://goo.gl/oSe8f1
Enter the Coupon "youtube" without quotations to get your discount.
Introduction 0:03
Older Air Brake Systems 1:25
Pre trip Inspection 3:30
Draining the Wet Tank 4:20
ADIS Systems (Air Dryer Integrated System) 6:18
Conclusion 8:48
Question - Where is the Air Dryer located on your vehicle? 11:04
Blooper 11:51
Most drivers’ manuals indicate that the air dryer is optional; however, this air brake components have been an integral part of a truck or bus' air brake system for more than a quarter century.
The air brake system's air dryer is located between the compressor and the first air tank. On older systems it is located between the compressor and the "wet" (supply) tank. On newer ADIS (Air Dryer Integrated Systems) the air dryer is located between the compressor and the primary and secondary air tanks (reservoirs).
There are two indicators of ADIS systems:
1) The governor is located within close physical proximity to the air dryer - often right beside the air dryer;
2) When building air pressure, an ADIS system will build either the secondary or primary sub-system to approximately 100 psi (pounds per square inch) and then build the other system.
When both systems attain approximately 100psi, both systems will build to maximum system pressure. When the air brake system attains maximum pressure the air dryer will purge, discharge or spit. The air dryer is the first indicator that the air brake system is at maximum pressure. Yet, when conducting a pre-trip inspection, a driver must confirm by the air gauges on the dash that yes, in fact, the system is at maximum pressure.
Good luck on your CDL Road Test!
************************
www.smartdrivetest.com
www.facebook.com/smartdrivetest
www.twitter.com/smartdrivetest
www.instagram.com/smartdrivetest/
Music: BoxCat Games
Nameless: The Hackers RPG Soundtrack - Epic Song
Видео How the Air Dryer Works to Pass CDL Air Brake Pre-Trip Inspection Test канала Smart Drive Test
Get 30% OFF Air Brake Course. Coupon "youtube30" CLICK THE LINK https://www.smartdrivetest.com/pass-cdl-air-brakes-course SEE TOPICS BELOW.
Get 25% OFF Air Brake Course. CLICK THE LINK https://goo.gl/oSe8f1
Enter the Coupon "youtube" without quotations to get your discount.
Introduction 0:03
Older Air Brake Systems 1:25
Pre trip Inspection 3:30
Draining the Wet Tank 4:20
ADIS Systems (Air Dryer Integrated System) 6:18
Conclusion 8:48
Question - Where is the Air Dryer located on your vehicle? 11:04
Blooper 11:51
Most drivers’ manuals indicate that the air dryer is optional; however, this air brake components have been an integral part of a truck or bus' air brake system for more than a quarter century.
The air brake system's air dryer is located between the compressor and the first air tank. On older systems it is located between the compressor and the "wet" (supply) tank. On newer ADIS (Air Dryer Integrated Systems) the air dryer is located between the compressor and the primary and secondary air tanks (reservoirs).
There are two indicators of ADIS systems:
1) The governor is located within close physical proximity to the air dryer - often right beside the air dryer;
2) When building air pressure, an ADIS system will build either the secondary or primary sub-system to approximately 100 psi (pounds per square inch) and then build the other system.
When both systems attain approximately 100psi, both systems will build to maximum system pressure. When the air brake system attains maximum pressure the air dryer will purge, discharge or spit. The air dryer is the first indicator that the air brake system is at maximum pressure. Yet, when conducting a pre-trip inspection, a driver must confirm by the air gauges on the dash that yes, in fact, the system is at maximum pressure.
Good luck on your CDL Road Test!
************************
www.smartdrivetest.com
www.facebook.com/smartdrivetest
www.twitter.com/smartdrivetest
www.instagram.com/smartdrivetest/
Music: BoxCat Games
Nameless: The Hackers RPG Soundtrack - Epic Song
Видео How the Air Dryer Works to Pass CDL Air Brake Pre-Trip Inspection Test канала Smart Drive Test
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
Truck Repairs: Air dryer purges constantlyHow to Determine Air Brake Adjustment—Applied—Pry Bar—Mark & MeasureBendix Full Air BoardReplacing air dryer filter and complete air dryer unitHow to Brake Downhill Safely | Air Brakes SmartHow to Drive & Shift 8, 9, 10, 13, 15 or 18 Transmissions | THEORYBasic CDL Air Brake ComponentsAir Brake Relay - How it Works. Air braking systems and Commercial vehiclesAir Brakes Supply CircuitHow to Do the CDL Air Brake Pre-Trip InspectionUnloader valveBendix Air Brake Video 1Replacing old style air dryer filterAir Brakes Explained Simply :: Service, Parking and Emergency Brakes One & the SameCDL Training - How to Pass Air Brakes Exam - Driving Academy (Part 1)Losing air pressureHow a Bendix Pura-Guard Air Dryer worksHow to Test The Governor for Air Brakes Course | Air Brakes SmartBendix Air Board Overview 1