WELDY extrusion welder booster EX2/ EX3 user guide
1. putting into operation
2. changing of welding shoe
1. Putting booster EX2/ EX3 into operation
-Welding can begin once the operating temperature has been attained. Operate the WELDY drive on/off switch for this purpose, Operate the WELDY tool only when feed welding rod of 3 or 4mm diameter into the welding rod opening and allow a small amount plasticized material to escape.
-Direct the WELDY welding shoe to the welding zone.
- Pre-warm the welding zone with back and forth movements.
-Carry out test welding and analysis.
-Adjust the hot air temperature using the air temperature potentiometer.
2. Changing of welding shoe
-Turn off the WELDY tool while warm and DISCONNECT from the power supply.
-Remove the WELDY welding shoe holder by unfastening the clamp screws from the extruder nozzle.
-Every time the welding shoe is changed, clean the extruder nozzle of welding residue and make sure that it is screwed in tightly.
-Remove WELDY welding shoe from the welding shoe holder by unfastening the fastening screws.
-Fasten the welding shoe, appropriate to the welding seam, onto the welding shoe holder with fastening screws, the welding shoe and welding shoe holder must be tightened properly with the clamp screws.
-Attach welding shoe unit to the extruder nozzle tightly by clamp screw.
To the product:
Booster EX2
https://www.leister.com/en/product/Booster-EX2/146-738
Booster EX3
https://www.leister.com/en/product/Booster-EX3/146-917
https://www.leister.com
#handextruder
#extrusionmachine
#plasticfabrication
0:00 booster EX2 / EX3 The extrusion welder for professionals 1. Putting into operation 2. Changing of welding shoe
0:12 booster EX2 / EX3 Putting into operation
2:20 booster EX2 / EX3 Changing of welding shoe
Видео WELDY extrusion welder booster EX2/ EX3 user guide канала WELDYhotairtools
2. changing of welding shoe
1. Putting booster EX2/ EX3 into operation
-Welding can begin once the operating temperature has been attained. Operate the WELDY drive on/off switch for this purpose, Operate the WELDY tool only when feed welding rod of 3 or 4mm diameter into the welding rod opening and allow a small amount plasticized material to escape.
-Direct the WELDY welding shoe to the welding zone.
- Pre-warm the welding zone with back and forth movements.
-Carry out test welding and analysis.
-Adjust the hot air temperature using the air temperature potentiometer.
2. Changing of welding shoe
-Turn off the WELDY tool while warm and DISCONNECT from the power supply.
-Remove the WELDY welding shoe holder by unfastening the clamp screws from the extruder nozzle.
-Every time the welding shoe is changed, clean the extruder nozzle of welding residue and make sure that it is screwed in tightly.
-Remove WELDY welding shoe from the welding shoe holder by unfastening the fastening screws.
-Fasten the welding shoe, appropriate to the welding seam, onto the welding shoe holder with fastening screws, the welding shoe and welding shoe holder must be tightened properly with the clamp screws.
-Attach welding shoe unit to the extruder nozzle tightly by clamp screw.
To the product:
Booster EX2
https://www.leister.com/en/product/Booster-EX2/146-738
Booster EX3
https://www.leister.com/en/product/Booster-EX3/146-917
https://www.leister.com
#handextruder
#extrusionmachine
#plasticfabrication
0:00 booster EX2 / EX3 The extrusion welder for professionals 1. Putting into operation 2. Changing of welding shoe
0:12 booster EX2 / EX3 Putting into operation
2:20 booster EX2 / EX3 Changing of welding shoe
Видео WELDY extrusion welder booster EX2/ EX3 user guide канала WELDYhotairtools
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
Superlight welder for thin membranes - miniwelder tex 1WELDY booster EX2/ EX3 - The powerful extrusion welderTutorial | HG 330/530-A - Memory functionWeldy Car Wrapping Kits in actionWELDY Pendulum-weldingWelding of Sarnafil T welding cord with WELDY energy 1600Weldy HG 330-S Car Wrapping KitTutorial | HG 530-A - ECO Mode (function1)WELDY - Hot air hand tool HT 530-AWELDY foiler ETL with laser beam guidanceWELDY -- Shrinking cables and tubesWELDY pitched roof welding with miniwelder roof2WELDY The new RW3400-combi T40roofer RW 3400 the professional lightweight welder for the roofTutorial | HG 530-A - ECO Mode (function 2)Weldy hot air heat gun Car Wrapping Kit HG530-A vs. HG330-BTutorial | HG 330/530-A - Selecting the temperature unitWeldy energy 1600 used for shrink fits, forming plastic sheets, pipe and rods.WELDY foilerOptimal threading of the miniwelder roof 2 for the perfect welding seam.Weldy hot air heat gun Car Wrapping Kit HG530-A