How to calibrate feed inclination sensor | SmartROC T40 | SmartROC T45
In this Epiroc 24/7 video, Mike Wentworth, an experienced Product and Application Specialist at Epiroc, demonstrates the process of calibrating the feed inclination sensor on SmartROC T40 and T45 machines. Discover a simple method using a four-foot level to align the sensor mechanically and achieve a zero angle. Learn how to verify and adjust the electronic readings on the screen to ensure accurate drilling results. Avoid deviations in hole positioning caused by sensor inaccuracies and achieve precise drilling performance.
Applies to the following models:
SmartROC T40 | SmartROC T45
#Epiroc247 #EquipmentMaintenance #SurfaceRigs
Warning: Read and follow all labels and the Owner’s Manual carefully before installing, operating, or servicing unit. Read the safety information at the beginning of the manual and in each section.
Disclaimer: Legal Notice © Copyright 2022. All product names in this video are trademarks of Epiroc. Any unauthorized use, broadcasting, transmission, copying or re-recording of the contents or any part thereof is prohibited. Photos and videos may show equipment with optional extras. No warranty is made regarding specifications or otherwise. Specifications and equipment are subject to change without notice. Under no circumstance will Epiroc be responsible or liable in any way for any content, including but not limited to, any errors or omissions in the content, or for any loss or damage of any kind incurred as a result of any content communicated in this video, whether by Epiroc or a third party. In no event shall Epiroc be liable for any direct, indirect, punitive, incidental, special consequential damages or any damages whatsoever resulting from loss of use, data or profits arising out of or in connection with the availability, use or performance of any information communicated in this video. Due to factors beyond the control of Epiroc, it cannot guarantee against improper use or unauthorized modification of this information. Epiroc assumes no liability for property damage or injury as a result of any of the information contained in this video. Use this information at your own risk. Epiroc recommends safe practiced when performing any do it yourself repairs and maintenance and or with tools seen or implied in this video. Due to factors beyond the control of Epiroc, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Epiroc.
Видео How to calibrate feed inclination sensor | SmartROC T40 | SmartROC T45 канала Epiroc USA
Applies to the following models:
SmartROC T40 | SmartROC T45
#Epiroc247 #EquipmentMaintenance #SurfaceRigs
Warning: Read and follow all labels and the Owner’s Manual carefully before installing, operating, or servicing unit. Read the safety information at the beginning of the manual and in each section.
Disclaimer: Legal Notice © Copyright 2022. All product names in this video are trademarks of Epiroc. Any unauthorized use, broadcasting, transmission, copying or re-recording of the contents or any part thereof is prohibited. Photos and videos may show equipment with optional extras. No warranty is made regarding specifications or otherwise. Specifications and equipment are subject to change without notice. Under no circumstance will Epiroc be responsible or liable in any way for any content, including but not limited to, any errors or omissions in the content, or for any loss or damage of any kind incurred as a result of any content communicated in this video, whether by Epiroc or a third party. In no event shall Epiroc be liable for any direct, indirect, punitive, incidental, special consequential damages or any damages whatsoever resulting from loss of use, data or profits arising out of or in connection with the availability, use or performance of any information communicated in this video. Due to factors beyond the control of Epiroc, it cannot guarantee against improper use or unauthorized modification of this information. Epiroc assumes no liability for property damage or injury as a result of any of the information contained in this video. Use this information at your own risk. Epiroc recommends safe practiced when performing any do it yourself repairs and maintenance and or with tools seen or implied in this video. Due to factors beyond the control of Epiroc, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Epiroc.
Видео How to calibrate feed inclination sensor | SmartROC T40 | SmartROC T45 канала Epiroc USA
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
![How to do a pre-shift/daily inspection | PowerROC T35 | PowerROC T45](https://i.ytimg.com/vi/hbpBHciHPvY/default.jpg)
![How to load a software program into RCS | Boomer, Boltec and Simba series with RCS 5](https://i.ytimg.com/vi/Nb3Xd4czSQw/default.jpg)
![How to differentiate between a pro and a manual bracket | VC series | ER series](https://i.ytimg.com/vi/NR2xr47Hsog/default.jpg)
![How to load and save parameters | SmartROC T40 | SmartROC T45](https://i.ytimg.com/vi/Y1hmd6dqA30/default.jpg)
![How to activate pressure washer | SmartROC D65 | SmartROC D60](https://i.ytimg.com/vi/078EcaRacKc/default.jpg)
![How to check and inspect nitrogen piston accumulator | HB2000](https://i.ytimg.com/vi/AWiKOu7MNq8/default.jpg)
![How to use an automatic greaser for underground rigs | Boomer E1 C-DH | Epiroc underground RCS](https://i.ytimg.com/vi/h0Tba02aBJ8/default.jpg)
![Epiroc Live ConExpo 2020 Ep 5/5: Surface Powerbit, DM30 II, SmartROC D60, Drum Cutter, TCO Service](https://i.ytimg.com/vi/hY5C_i1ObqI/default.jpg)
![How to adjust sliding pieces | SmartROC T35/T40/T45-10 | FlexiROC T15/20/30/35/40R | FlexiROC D60/65](https://i.ytimg.com/vi/fqlxoq9EEms/default.jpg)
![How to charge an EC breaker nitrogen accumulator](https://i.ytimg.com/vi/CFA0brM-Aak/default.jpg)
![How to use HATCON for your fleet](https://i.ytimg.com/vi/HTkBeHU08yI/default.jpg)
![How to inspect a hydraulic breaker | EC40-EC135](https://i.ytimg.com/vi/rYhv40sb94w/default.jpg)
![Have you heard this RULE OF THUMB for starting RPM?](https://i.ytimg.com/vi/iT74IBvgmdw/default.jpg)
![How to adjust watermist | PowerROC T35 | PowerROC T45](https://i.ytimg.com/vi/Qhw3SQSdfqs/default.jpg)
![Your drill rig's tracks can SLIP OFF if THIS isn't checked?!](https://i.ytimg.com/vi/nUo2LwlLWho/default.jpg)
![How to start and stop a rig | Epiroc PowerROC D60](https://i.ytimg.com/vi/N_4umYWxzCY/default.jpg)
![How to check proper electric motor rotation | Diamec Smart 8](https://i.ytimg.com/vi/mvWhTM0wleM/default.jpg)
![How to calibrate the boom | FlexiROC D60 | FlexiROC D65](https://i.ytimg.com/vi/KHGjHkykUWg/default.jpg)
![Mining with Moira: RigScan - ft. Dan Patrick](https://i.ytimg.com/vi/35kocWM-TWs/default.jpg)
![How to set M-stop positions | SmartROC T35 | SmartROC T40 | SmartROC T45](https://i.ytimg.com/vi/zrxIC00gCOE/default.jpg)
![How to unload an Epiroc SmartROC D65-10](https://i.ytimg.com/vi/wP4TcMMcO5Y/default.jpg)