First Aluminum Test Run with MPCNC
This is the very first test run I did...after some adjustment of speeds I was able to get it cutting pretty nice even with a dull bit..the slot in the picture at the end was done with the trochodial setting in estlCam. Again, pretty impressive cut and surface finish for the first try.
Видео First Aluminum Test Run with MPCNC канала Mayberry Custom
Видео First Aluminum Test Run with MPCNC канала Mayberry Custom
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
![More Aluminum Cutting on the Mostly Printed CNC](https://i.ytimg.com/vi/zefnrPRvc9Q/default.jpg)
![mpcnc build more sub assembly, And the frame assembly EP2/4](https://i.ytimg.com/vi/9mgm96PqzuA/default.jpg)
![OpenBuilds MiniMill Review (mostly for cutting aluminum)](https://i.ytimg.com/vi/4KVWpFGqT1I/default.jpg)
![Graz Makes: The MPCNC (mostly printed cnc machine)](https://i.ytimg.com/vi/RJRHGbYTbU0/default.jpg)
![MPCNC Primo upgrade from Burley: introduction](https://i.ytimg.com/vi/acT4xNRaKeU/default.jpg)
![IndyMill - Open Source DIY CNC Machine #4 Final Test!](https://i.ytimg.com/vi/5jFCecZdbGs/default.jpg)
![Cutting Aluminum on a Mostly Printed CNC (MPCNC)](https://i.ytimg.com/vi/k-2kr4tGEIQ/default.jpg)
![Portable MPCNC by Steve M. Potter - Dublin Maker 2021](https://i.ytimg.com/vi/ztcMPmEYCmw/default.jpg)
![MPCNC W/ Dual End Stops Overview](https://i.ytimg.com/vi/urwEC40-d8E/default.jpg)
![Building the MPCNC the hard way - Episode 7 ( First Cut )](https://i.ytimg.com/vi/HPah95nxX7s/default.jpg)
![MPCNC Automatic Tool Changer](https://i.ytimg.com/vi/OTaon2fveP4/default.jpg)
![Protips before you build your own MPCNC (Mostly Printed CNC machine)](https://i.ytimg.com/vi/UfgTD5m9dA4/default.jpg)
![CNC FRÄSE Arduino und Estlcam](https://i.ytimg.com/vi/twwr-l1EV1Y/default.jpg)
![Vorstellung meiner Alu CNC Portalfräse](https://i.ytimg.com/vi/leGGwITuAn8/default.jpg)
![ShopBuilt - How to Anodize Aluminum!](https://i.ytimg.com/vi/P8oesBi7_II/default.jpg)
![Brushless Spindle for CNC Milling.](https://i.ytimg.com/vi/CmqrG8ywcic/default.jpg)
![DIY 3D PRINTED CNC machine with NEMA 23 stepper motors PART 2 - Test Milling operations.](https://i.ytimg.com/vi/nor6gWpcx8c/default.jpg)
![MPCNC Support Universels pour Tubes dépassants 80cm [FR-EN-US]](https://i.ytimg.com/vi/Qe_rvyKOhfY/default.jpg)
![No Boot Dust Collection on the CNC Router](https://i.ytimg.com/vi/t-AeqebDAHo/default.jpg)
![MPCNC Build](https://i.ytimg.com/vi/O3N5tAFIMpI/default.jpg)