BLV Cube 3D Printer with Misumi frame extrusion - first moves #BLVCube #3DPrinter
BLV Cube 3D Printer with Misumi frame extrusion, drilled and cut by Misumi USA - first movement tests.
No Commentary - Edit (2/12/2021): Seeing as this video is still getting a good amount of views and I now have an amazing amount of printing hours I will work on a video next week. The SLS parts are holding up amazing with no signs of wear, the belts have not had any issue with the split bearing design that worried some builders early on. I did have some magnet issues where I did not get the clearances right, allowing the magnets to break loose over time. I opted to put a magnetic sheet on the bed and that has been fine. I did have some extruder issues with various generic BMG clones, and I even wore out a real BMG! Titan Extruder ran fine.
Maintenance has been easy, switching extruders has not been all that hard. The stock BLV Cube cooling fan setup works well enough for most prints but there are nice mods on Thingiverse that are better. I still have a loose t-nut that will vibrate at certain speeds making the machine louder than it should be. At slow speeds, the machine is fairly equal to my Railcore ii 300ZL.
Build ease: In my opinion, if this is your first printer build or you are still learning to build this machine will be a bit more challenging than say a Prusa. Ben Levi has great directions that if followed carefully will make it easier to construct. I did have to backtrack a few times when working on the X-axis to correct mistakes.
Print quality with the right linear rails is pretty amazing, make sure you opt for good Z screws and nuts to prevent any unwanted z wobble artifacts. I went with MGN15 rails instead of MGN12 on the Z-axis and this produces some of the best-looking prints along that axis very near to the quality produced by a Voron or my belted Z printer. The bed is heavy so adding a bearing on top of the Z stepper will help prevent stress and improve print quality.
Thanks for watching, please subscribe and help my channel grow!
#3DPrinting #BLV #BLVCube #Johns3DPrintingCorner
Видео BLV Cube 3D Printer with Misumi frame extrusion - first moves #BLVCube #3DPrinter канала John's 3D Printing Corner
No Commentary - Edit (2/12/2021): Seeing as this video is still getting a good amount of views and I now have an amazing amount of printing hours I will work on a video next week. The SLS parts are holding up amazing with no signs of wear, the belts have not had any issue with the split bearing design that worried some builders early on. I did have some magnet issues where I did not get the clearances right, allowing the magnets to break loose over time. I opted to put a magnetic sheet on the bed and that has been fine. I did have some extruder issues with various generic BMG clones, and I even wore out a real BMG! Titan Extruder ran fine.
Maintenance has been easy, switching extruders has not been all that hard. The stock BLV Cube cooling fan setup works well enough for most prints but there are nice mods on Thingiverse that are better. I still have a loose t-nut that will vibrate at certain speeds making the machine louder than it should be. At slow speeds, the machine is fairly equal to my Railcore ii 300ZL.
Build ease: In my opinion, if this is your first printer build or you are still learning to build this machine will be a bit more challenging than say a Prusa. Ben Levi has great directions that if followed carefully will make it easier to construct. I did have to backtrack a few times when working on the X-axis to correct mistakes.
Print quality with the right linear rails is pretty amazing, make sure you opt for good Z screws and nuts to prevent any unwanted z wobble artifacts. I went with MGN15 rails instead of MGN12 on the Z-axis and this produces some of the best-looking prints along that axis very near to the quality produced by a Voron or my belted Z printer. The bed is heavy so adding a bearing on top of the Z stepper will help prevent stress and improve print quality.
Thanks for watching, please subscribe and help my channel grow!
#3DPrinting #BLV #BLVCube #Johns3DPrintingCorner
Видео BLV Cube 3D Printer with Misumi frame extrusion - first moves #BLVCube #3DPrinter канала John's 3D Printing Corner
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
![Making BLV MGN cube 3D printer](https://i.ytimg.com/vi/-ZlDRSxjoqY/default.jpg)
![CroXY Crossed Gantry 3D Printer](https://i.ytimg.com/vi/Kx4VfzS_V6c/default.jpg)
![clothes/T-shirt/fabric silicone ink Embossing Process, silicone embossing Machine Operation Tutorial](https://i.ytimg.com/vi/Z8-JGHRO6eQ/default.jpg)
![Upgrading the MK3 with genuine HIWIN linear rails: Worth it?](https://i.ytimg.com/vi/J_RcgixLbAI/default.jpg)
![Pellet Extrusion 3D Printing on the Atlas](https://i.ytimg.com/vi/QB4HyC4gIDc/default.jpg)
![Kinematically-Coupled 3D Printer Bed Proof of Concept](https://i.ytimg.com/vi/a9irK9rOUHY/default.jpg)
![BLV Ender 3 Pro - Bed assembly](https://i.ytimg.com/vi/Ezdl2pPzPiA/default.jpg)
![Hero Me Gen 5: The ultimate part cooling fan duct for Creality 3D printers?](https://i.ytimg.com/vi/DUkoKzOFWFs/default.jpg)
![Fixing Z Wobble from 20$ Ball Screws with that simple device](https://i.ytimg.com/vi/mqSQhwqSzvg/default.jpg)
![MRRF 2019: CoreXY 3D Printer Compilation](https://i.ytimg.com/vi/ifQt9VfWZ1Y/default.jpg)
![3D Printing with ODrive V3-Go FAST !](https://i.ytimg.com/vi/mAVZT7hIMLw/default.jpg)
![Tool-Changer Update with Stall Detection](https://i.ytimg.com/vi/fRo3FUWs4Sg/default.jpg)
![Oasis 3DP, an open source powder and inkjet 3D printer](https://i.ytimg.com/vi/lIVdwP0RAN8/default.jpg)
![BLV MGN first move](https://i.ytimg.com/vi/tbGUkDDD0v4/default.jpg)
![Duet 2 Wifi for CNC Router Machine?](https://i.ytimg.com/vi/kOg1t_WBIIU/default.jpg)
![BLV mgn Cube - Front belt tensioner assembly](https://i.ytimg.com/vi/O5G3dKr_gxg/default.jpg)
![Why direct drive is not automatically better than bowden tube](https://i.ytimg.com/vi/ybTbuUBy2-s/default.jpg)
![x carriageBLV mgn Cube: Metal kit - X Carriage assembly instructions](https://i.ytimg.com/vi/eE851Lm2ddo/default.jpg)
![The Best 3D Printer Kit Money Can Buy in 2021?](https://i.ytimg.com/vi/91xe7UfFMgY/default.jpg)
![resonnance test 100mm/sec blv MGN metal kit nf crazy plus](https://i.ytimg.com/vi/UkFa6o_Uuig/default.jpg)