#102 Hypercube Evolution 3D Printer Build - 9 (BLTouch Sensor)
In this video I take a look at setting up the BL Touch sensor for use with the BigTreeTech SKR V1.3 board on the printer. Actually I will be using a 3D Touch which is a Chinese copy of the BL Touch. I also setup the bed levelling at the same time.
I have covered off on getting the environment setup to make changes to the Marlin 2.0 firmware in another video, you can find it here:
https://youtu.be/4-vrkHP0v78
A big thank you to Scott 3D who published the design for the printer on Thingiverse, link below.
I will be providing any design files that I produce where there are changes so feel free to use and abuse anything I make available as you see fit as well.
https://www.thingiverse.com/thing:2254103
Here is a link to the facebook group for the Hypercube Evolution
https://www.facebook.com/groups/Hypercubeevolution/
If you like what you see, then please like and subscribe, you can also check out more information at my website:
http://www.grumpyoldtech.technology
or take a look at my Facebook page:
https://fb.me/GrumpyOldTech
If you want to get in contact, leave a comment or email me at
GrumpyOldTech@outlook.com.au
Видео #102 Hypercube Evolution 3D Printer Build - 9 (BLTouch Sensor) канала Grumpy Old Tech
I have covered off on getting the environment setup to make changes to the Marlin 2.0 firmware in another video, you can find it here:
https://youtu.be/4-vrkHP0v78
A big thank you to Scott 3D who published the design for the printer on Thingiverse, link below.
I will be providing any design files that I produce where there are changes so feel free to use and abuse anything I make available as you see fit as well.
https://www.thingiverse.com/thing:2254103
Here is a link to the facebook group for the Hypercube Evolution
https://www.facebook.com/groups/Hypercubeevolution/
If you like what you see, then please like and subscribe, you can also check out more information at my website:
http://www.grumpyoldtech.technology
or take a look at my Facebook page:
https://fb.me/GrumpyOldTech
If you want to get in contact, leave a comment or email me at
GrumpyOldTech@outlook.com.au
Видео #102 Hypercube Evolution 3D Printer Build - 9 (BLTouch Sensor) канала Grumpy Old Tech
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
![Hypercube Evolution - #1Introduction](https://i.ytimg.com/vi/1rctCsUGnX8/default.jpg)
![Marlin Firmware Config - Core XY - SKGO - Chris's Basement](https://i.ytimg.com/vi/tK_YqSbDpZ4/default.jpg)
![FR - HyperCube Evolution - Tuto 5 : Installation Plateau, Extrudeur, Tete et Branchements Carte](https://i.ytimg.com/vi/0DP2d91u5FM/default.jpg)
![#103 Hypercube Evolution 3D Printer Build - 10 (Heat bed and Hot End)](https://i.ytimg.com/vi/n047iGfRnrU/default.jpg)
![Triple z axis - True bed leveling!](https://i.ytimg.com/vi/zqdJ47OT_BQ/default.jpg)
![Autoleveling on 3D printers: 9 myths and 12 sensors tested!](https://i.ytimg.com/vi/il9bNWn66BY/default.jpg)
![HevORT 3D Printer - Triple Independent Motors Z axis with self leveling bed.](https://i.ytimg.com/vi/yAEHdjro5Pc/default.jpg)
![#101 Hypercube Evolution 3D Printer Build - 8 (End Stops)](https://i.ytimg.com/vi/4-vrkHP0v78/default.jpg)
![BLTouch Setup on an Anet A8 with Marlin Firmware](https://i.ytimg.com/vi/WWDkZtWwd6I/default.jpg)
![#098 Hypercube Evolution 3D Printer Build - 7 (Mechanically complete, mostly)](https://i.ytimg.com/vi/nTQkxUDF7Pg/default.jpg)
![#106 Hypercube Evolution 3D Printer Build - 13 (Fine Tuning)](https://i.ytimg.com/vi/qnFf8Q_oh90/default.jpg)
![#097 Hypercube Evolution 3D Printer Build - 6 (Build Plate & Titan Aero)](https://i.ytimg.com/vi/ffOvE6yw4bA/default.jpg)
![SKR V1.3 + TMC2130 - MODIFICAÇÃO, INSTALAÇÃO E CONFIGURAÇÃO](https://i.ytimg.com/vi/ZtGpD0ySFvU/default.jpg)
![Build: Hypercube Evolution - Part 4 - CoreXY Belts](https://i.ytimg.com/vi/2wRE7E4HkXU/default.jpg)
![Triple Z motors - Self levelling print bed demo - HevORT Advanced DIY 3D Printer](https://i.ytimg.com/vi/aL7pEEHTTe4/default.jpg)
![HyperCube Evolution #7 - Build Platform Assembly](https://i.ytimg.com/vi/fWTbV11DwOs/default.jpg)
![3D Printer Battle: Prusa i3 MKS2 vs. My Hypercube](https://i.ytimg.com/vi/zoCL8obFkHE/default.jpg)
![HyperCube Evolution #8 - RAMPS 24v mod + "It's alive"](https://i.ytimg.com/vi/8Nmmrp4hKeM/default.jpg)
![EP.08 - Building a 3D-Printer - Hypercube evolution](https://i.ytimg.com/vi/A4LXYKb9wY4/default.jpg)
![EP.06 - Building a 3D-Printer - Hypercube evolution](https://i.ytimg.com/vi/JlHpW1g8s_s/default.jpg)