Загрузка...

World’s First Sub-1 Minute Benchy (00:54.733) – New World Record

There’s still a bit of room for improvement. The chimney is a mess, and at the upper section of the boat’s cabin the part cooling wasn’t strong enough to cool the filament properly. But overall, I’m really happy with how this turned out. Big thanks to my Patreons who have supported me on this long journey for over three years. You’re truly amazing!

Видео World’s First Sub-1 Minute Benchy (00:54.733) – New World Record канала Matt The Printing Nerd
Комментарии отсутствуют
Зарегистрируйтесь или войдите с
Информация о видео
2 марта 2026 г. 23:36:49
00:00:59
Matt The Printing Nerd
Правообладателям
Жалоба на материал Недопустимый материал Нарушение авторских прав
Комментарии
Поделиться
Другие видео канала

Testing my new fan duct. Look at those top layersTesting my new fan duct. Look at those top layers

THE 100 Assembly Guide - Part 3: Bottom FrameTHE 100 Assembly Guide - Part 3: Bottom Frame

How to Choose the Fastest Motors for your 3D PrinterHow to Choose the Fastest Motors for your 3D Printer

THE 100 Assembly Guide - Part 1: ToolheadTHE 100 Assembly Guide - Part 1: Toolhead

The first print on my new THE 100 construction - Calibration Cube at 180mm/s perimeter speedThe first print on my new THE 100 construction - Calibration Cube at 180mm/s perimeter speed

THE 100 Assembly Guide - Part 4: Software InstallationTHE 100 Assembly Guide - Part 4: Software Installation

PA Tuning at 1200mm/s at 280k accelerationPA Tuning at 1200mm/s at 280k acceleration

1000mm/s at 30k acceleration on THE 100 - Testing maximum volumetric flow rate1000mm/s at 30k acceleration on THE 100 - Testing maximum volumetric flow rate

THE 100 - The dethroned speed champion... even faster!THE 100 - The dethroned speed champion... even faster!

Testing the updated Toolhead of THE 100Testing the updated Toolhead of THE 100

THE 100 Assembly Guide - Part 2: Top FrameTHE 100 Assembly Guide - Part 2: Top Frame

The 100 - The worlds fastest 3D Printer based on a printed FrameThe 100 - The worlds fastest 3D Printer based on a printed Frame

The 100 in Action - First layer at 100mm/sThe 100 in Action - First layer at 100mm/s

THE 100 Assembly Guide - Part 5: Electric InstallationTHE 100 Assembly Guide - Part 5: Electric Installation

Why is THE 100's print bed so small? - Q&AWhy is THE 100's print bed so small? - Q&A

T250 - The World's Fastest 3D PrinterT250 - The World's Fastest 3D Printer

If you can print it fast, you can print it slow - The 100 print quality comparisonIf you can print it fast, you can print it slow - The 100 print quality comparison

Not an Ender 3 anymore...Not an Ender 3 anymore...

T250 in Action - Printing the new Toolhead at 1200 mm/s and 160k Acceleration #3dprinting #diy #fastT250 in Action - Printing the new Toolhead at 1200 mm/s and 160k Acceleration #3dprinting #diy #fast

Testing my new Z-AxisTesting my new Z-Axis

4000mm/s at 280k acceleration on the T250 - A new beast has entered the arena4000mm/s at 280k acceleration on the T250 - A new beast has entered the arena

Яндекс.Метрика
© 2008-2026 «Информационно-развлекательный портал города Верхняя Салда»
salda.ws@mail.ru salda_ws Контакты Карта портала Сообщить об ошибке Соглашения Пользовательское соглашение Соглашение о конфиденциальности Согласие на обработку персональных данных Информация для правообладателей Об использовании Cookies
Все заметки Новая заметка Страницу в заметки
Страницу в закладки Мои закладки
На информационно-развлекательном портале SALDA.WS применяются cookie-файлы. Нажимая кнопку Принять, вы подтверждаете свое согласие на их использование.
О CookiesНапомнить позжеПринять