Shop Talk 19: Parting Tools
I'm often asked to talk about parting tools and the different types. This was my attempt at the discussion but I feel like I missed something. Perhaps this is a better subject for me during an actual job at hand.
There are two basic types of parting tool, high speed, and carbide, or carbide insert. Carbide inserts are great for production, and everyday use in the working shop. They have great chip formation and can run at higher speeds. However that can pose problems on smaller or less rigid lathes.
High speed steel would be my first pick, especially for home and hobby use. They can be easily re-sharpened and will last for years. You can have an assortment of blades each with a different grind on the end. They have less tool pressure and can run at low speeds.
One key point to remember, if your having chatter problems, often times reducing the RPM, and feeding in harder it will reduce or eliminate the chatter. Always make sure you have a good sharp tool, or a good insert that isn't burned up, and your tip is on center or just slightly above.
Hopefully my viewers will get something out of the video, and I'll be sure to touch on this subject as it arises later.
Edge Technology Pro Lathe Gage http://www.edgetechnologyproducts.com/pro-lathe-gage/
Parting tools on Amazon http://amzn.to/2vg9zQH
If you'd like to help support this channel and the shop, check me out on Patreon. https://www.patreon.com/abom79
T-shirts always available https://storefrontier.com/collections/abom79
Видео Shop Talk 19: Parting Tools канала Abom79
There are two basic types of parting tool, high speed, and carbide, or carbide insert. Carbide inserts are great for production, and everyday use in the working shop. They have great chip formation and can run at higher speeds. However that can pose problems on smaller or less rigid lathes.
High speed steel would be my first pick, especially for home and hobby use. They can be easily re-sharpened and will last for years. You can have an assortment of blades each with a different grind on the end. They have less tool pressure and can run at low speeds.
One key point to remember, if your having chatter problems, often times reducing the RPM, and feeding in harder it will reduce or eliminate the chatter. Always make sure you have a good sharp tool, or a good insert that isn't burned up, and your tip is on center or just slightly above.
Hopefully my viewers will get something out of the video, and I'll be sure to touch on this subject as it arises later.
Edge Technology Pro Lathe Gage http://www.edgetechnologyproducts.com/pro-lathe-gage/
Parting tools on Amazon http://amzn.to/2vg9zQH
If you'd like to help support this channel and the shop, check me out on Patreon. https://www.patreon.com/abom79
T-shirts always available https://storefrontier.com/collections/abom79
Видео Shop Talk 19: Parting Tools канала Abom79
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
![QTR 22 Accusize Parting Tool Kit Tested](https://i.ytimg.com/vi/A8TkXbBwZ3s/default.jpg)
![Turning Weld Build Up With High Speed Steel](https://i.ytimg.com/vi/GST14cz0U1U/default.jpg)
![Custom Internal Shaping Bar Part 4](https://i.ytimg.com/vi/wlDiVhIYaK0/default.jpg)
![Get your parts to run true in a non adjustable chuck. YOU MUST WATCH THIS!](https://i.ytimg.com/vi/gCUkJydSmdA/default.jpg)
![Let's make low profile side clamps!](https://i.ytimg.com/vi/E5pW4PDv6JU/default.jpg)
![A Brief Chat about Carbide Tooling](https://i.ytimg.com/vi/rsFFWYo8ugw/default.jpg)
![Acme Thread Lead Screw for Tailstock](https://i.ytimg.com/vi/PqtAdjXa_HU/default.jpg)
![Basics of a Parting Tool](https://i.ytimg.com/vi/5LtYzjR1JuM/default.jpg)
![Testing some $1.50 USD CNMG 432 inserts and a holder from Banggood, surprising results...!!!](https://i.ytimg.com/vi/zUpBZW1YlFw/default.jpg)
![Parting on the Lathe](https://i.ytimg.com/vi/fZlWJ_JqQtA/default.jpg)
![Cheap VS Expensive Tool Holders and Inserts](https://i.ytimg.com/vi/HjIbSPsoKuQ/default.jpg)
![10 More Shop Do's & Don'ts](https://i.ytimg.com/vi/8InaxcDV6P0/default.jpg)
![Lathe Tool Cutter Height Gauge](https://i.ytimg.com/vi/iNhQYFsou1Y/default.jpg)
![Saturday Night Special 141: Stuck Wilton Vise, ZTFab Grinder Racks, Abom79 Hoodies!](https://i.ytimg.com/vi/DWMwFaCoT1o/default.jpg)
![Drilling Large Holes in Cast Iron with a Trepan Tool!](https://i.ytimg.com/vi/2HEruBtaC1c/default.jpg)
![Banggood Parting tool Review](https://i.ytimg.com/vi/E2h5eexVE_0/default.jpg)
![SNS 306 Part 1: Okuma Tool Block Modifications](https://i.ytimg.com/vi/1W8xUj2VeBg/default.jpg)
![Grinding HSS Tools](https://i.ytimg.com/vi/__A2xtLF0AU/default.jpg)