Tormach 1300PL Plasma Table Installation Video
The 1300PL Plasma Table was designed to be easily delivered and installed by the customer. It arrives on a pallet, so no forklift is necessary, just a couple 4 x 4's and an engine hoist to remove it from the pallet and tip it down to the ground. We estimate that it will take approximately two hours to setup and start running.
To help our customers, Tormach supplies an Owner's Manual that goes through all the steps of setting up and running the Tormach 1300PL Plasma Table. In addition, we also provide installation videos to supplement the Owner's Manual.
Chapter Links for the Video:
0:00 Introduction
0:28 Operator Manual
0:45 Moving the Crate
1:16 Unpack the Crate
1:52 Remove Frame from the Crate
4:05 Lowering the Table to its Feet
4:45 Install the Rear Legs
5:17 Level the Machine Frame
7:10 Install the Side Panel and Cable Carriers
9:03 Install the Plasma Torch and Lead
13:14 Install Machine Arm and Controller
15:03 Install the Slats and Fill the Water Table
15:58 Verify the Installation
18:42 Testing the Plasma Source Control
19:15 Test Torch Breakaway
19:38 Test the Ohmic Probing
21:58 Setup the PathPilot Controller
Please download the 1300PL Plasma Table Owner's Manual here: https://tormach.com/docs/download/assetlink/asset_id/609
P.S.: Never run your water table with any pets in the vicinity of the plasma torch.
Be sure to subscribe for updates on everything Tormach: https://goo.gl/sWeCs7
About Us:
At Tormach, we're dedicated to providing exceptionally engineered products, technical support, and customer service at the lowest possible cost. Our focus is to help you realize your CNC goals through tools and resources that transform your concepts into real products. Connect with us:
Visit our website: https://www.tormach.com
Facebook: https://www.facebook.com/tormach
Instagram: https://www.instagram.com/tormach
Twitter: https://twitter.com/tormach
LinkedIn: https://www.linkedin.com/company/tormach/
Видео Tormach 1300PL Plasma Table Installation Video канала Tormach Inc.
To help our customers, Tormach supplies an Owner's Manual that goes through all the steps of setting up and running the Tormach 1300PL Plasma Table. In addition, we also provide installation videos to supplement the Owner's Manual.
Chapter Links for the Video:
0:00 Introduction
0:28 Operator Manual
0:45 Moving the Crate
1:16 Unpack the Crate
1:52 Remove Frame from the Crate
4:05 Lowering the Table to its Feet
4:45 Install the Rear Legs
5:17 Level the Machine Frame
7:10 Install the Side Panel and Cable Carriers
9:03 Install the Plasma Torch and Lead
13:14 Install Machine Arm and Controller
15:03 Install the Slats and Fill the Water Table
15:58 Verify the Installation
18:42 Testing the Plasma Source Control
19:15 Test Torch Breakaway
19:38 Test the Ohmic Probing
21:58 Setup the PathPilot Controller
Please download the 1300PL Plasma Table Owner's Manual here: https://tormach.com/docs/download/assetlink/asset_id/609
P.S.: Never run your water table with any pets in the vicinity of the plasma torch.
Be sure to subscribe for updates on everything Tormach: https://goo.gl/sWeCs7
About Us:
At Tormach, we're dedicated to providing exceptionally engineered products, technical support, and customer service at the lowest possible cost. Our focus is to help you realize your CNC goals through tools and resources that transform your concepts into real products. Connect with us:
Visit our website: https://www.tormach.com
Facebook: https://www.facebook.com/tormach
Instagram: https://www.instagram.com/tormach
Twitter: https://twitter.com/tormach
LinkedIn: https://www.linkedin.com/company/tormach/
Видео Tormach 1300PL Plasma Table Installation Video канала Tormach Inc.
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
Steel Frame Fabrication - DIY CNC Plasma Table - Ep. 1CrossFire XR vs Pro - Langmuir System's tables compared side by side.Pawlowski GmbH - Plasmacut schneidenThe New CNC Table is Here and IT'S INSANE!Assembling a Tormach 15L Slant Pro Lathe and Running My First PartThe New Tormach 1300PL Plasma Table with SpecificationsCUSTOM CNC PLASMA TABLE BUILD!!Actually Using the CNC Plasma Cutter // Lift Arc Builds: Cutting Out Well Top MoldsHow to build a CNC Plasma Cutter Table | Frame | Free Plans & CAD FilesHow to buy a CrossFire Pro - Lessons learned after 1 year with Langmuir Systems plasma cutting tableLangmuir Systems Crossfire XR - Unboxing Through First Cut!Making plasma cutting trackPlasmaCut - ZubehörTormach PathPilot Operator Console Installation for 770M/MX and 1100M/MX MillsTOP zváračka Kowax GeniTig200 AC/DC pre zváranie hliníka ocele a nehrdzavejúcej ocele MMA/TIG PulzHow to Build a CNC Plasma Cutting Table | Part 3 - The X, Y & Z ComponentsLds Cnc 5x10 Running Hypertherm 8The new Crossfire PRO CNC plasma table from Langmuir systemsKjellberg Cutting Technology- Cutfire 100i