DIY Glass Insert Live Edge River Table Tutorial
Love Of The Grain Workshop
So here is a project I’ve been working on in the evenings. A Live Edge Slab River Table with Glass Insert. To fit the glass I have to square everything up and route a 1/4” down each inside edge. I could do it freehand but I would most definitely go off and have a wavy edge instead of a straight one. So i lay the glass on the wood and draw lines down either side. I make sure my bit only comes down out of the bottom of he @boschtoolsna router plate by 1/4”. A fraction less actually so I can sand it perfectly smooth afterwards and still have 1/4” routed out. I then measured from the outer edge of the router to the outer most tip of the bit I was using. Which was 2-3/4”. So I then measure out from the inside pencil line on the wood 2-3/4”. This is then where I will clamp down a strip of steel. This creates a perfectly measured guide for my router edge to run down. So that the bit will run perfectly down the pencil line I drew first. Then so that my router doesn’t lean or tilt on either side (which would cause the bit to dig into the cutting area, making it uneven) I lay my other piece of wood close to the edge I’m routing so that it has a flat level edge to run down on both sides. Thus creating an almost perfectly level flat routed area. Once both edges are routed out completely. I sand with a 120 grit making it flat and super smooth for the glass to fit into too. Then insert glass!!
Feel free to contact me for a quote on a custom piece of your own. Also check out my
facebook
https://www.facebook.com/LoveOfTheGrainWorkshop/
Instagram
Www.instagram.com/Love_of_the_grain_workshop
And I typically have some stock items available on my Etsy page as well. http://etsy.me/2n87ZwG
Видео DIY Glass Insert Live Edge River Table Tutorial канала Love Of The Grain Workshop
So here is a project I’ve been working on in the evenings. A Live Edge Slab River Table with Glass Insert. To fit the glass I have to square everything up and route a 1/4” down each inside edge. I could do it freehand but I would most definitely go off and have a wavy edge instead of a straight one. So i lay the glass on the wood and draw lines down either side. I make sure my bit only comes down out of the bottom of he @boschtoolsna router plate by 1/4”. A fraction less actually so I can sand it perfectly smooth afterwards and still have 1/4” routed out. I then measured from the outer edge of the router to the outer most tip of the bit I was using. Which was 2-3/4”. So I then measure out from the inside pencil line on the wood 2-3/4”. This is then where I will clamp down a strip of steel. This creates a perfectly measured guide for my router edge to run down. So that the bit will run perfectly down the pencil line I drew first. Then so that my router doesn’t lean or tilt on either side (which would cause the bit to dig into the cutting area, making it uneven) I lay my other piece of wood close to the edge I’m routing so that it has a flat level edge to run down on both sides. Thus creating an almost perfectly level flat routed area. Once both edges are routed out completely. I sand with a 120 grit making it flat and super smooth for the glass to fit into too. Then insert glass!!
Feel free to contact me for a quote on a custom piece of your own. Also check out my
https://www.facebook.com/LoveOfTheGrainWorkshop/
Www.instagram.com/Love_of_the_grain_workshop
And I typically have some stock items available on my Etsy page as well. http://etsy.me/2n87ZwG
Видео DIY Glass Insert Live Edge River Table Tutorial канала Love Of The Grain Workshop
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
10” Rikon Bandsaw cutting some fireplace mantel corbelsOrtur laser combined with Lightburn is amazing! #lightburn #ortur #laserengravingDM for your customized item now! #fractalburning #americanwhiskey #satisfyingvideo #lightburn #orturFractal burned resin wall art surfboard completed!#upcycle #diningtable #furnitureDIY Silicone Mold Making For Epoxy Resin & Soaps Using Incredible Solutions Mold PuttyCustom triple live edge oak slab steel leg coffee tableLove this staining technique! Steel wool & vinegar! #woodworkersofig #epoxywoodwork #satisfyingvideoBatch of Barrel Stave Flight Boards coming right up for Hidden Ships Distillery #flightboard #laser20% off all currently made products through the end of 2023! DM me for info! Shipping available.#satisfyingvideo #woodworking #epoxy #bartop @promiseepoxy#protip #woodrepair #woodworkingDIY Shousugiban Style German Shiplap Accent WallSavage & Cooke Lil Guero 7Y Bourbon & Guero 6Y Rye ReviewWhich color is your favorite?Van Leeuwen Pizza, Grey Poupon & Honey Cornbread Ice Cream Taste Test!#handmade #charcuterie #foodieOne of my favorite barn door builds! Modern & Sleek18’ resin rover banquet table. #satisfyingvideo #epoxy #woodworkersofig #wood #epoxywoodworkingOne of my favorite builds to date. Custom oval dining table & bench. Walnut live edge slabs & resin#woodworkersofig #woodworking #epoxywoodworking #satisfyingvideo #epoxy #art